Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
techtalk:evo:carb01f [2019/10/17 16:22] hippysmack [Repairing a Broken Enrichener Knob] |
techtalk:evo:carb01f [2024/01/02 21:16] (current) hippysmack |
||
|---|---|---|---|
| Line 9: | Line 9: | ||
| Any knob with a set screw will work as a replacement or you can find something like a large dice or mini Q-ball, drill a hole and epoxy it on. \\ | Any knob with a set screw will work as a replacement or you can find something like a large dice or mini Q-ball, drill a hole and epoxy it on. \\ | ||
| - | You can go to your local home improvement store and purchase a nice looking kitchen drawer pull knob. ((Simon of the XLFORUM http://xlforum.net/forums/showthread.php?t=46782&page=3)) \\ | + | You can go to your local home improvement store and purchase a nice looking kitchen drawer pull knob. ((Simon of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/28235-e-z-choke-knob-removal-new-knob-install/page3?t=46782&page=3)) \\ |
| Enlarge the hole with a drill bit to rod and then glue it in place with epoxy. \\ | Enlarge the hole with a drill bit to rod and then glue it in place with epoxy. \\ | ||
| - | {{:techtalk:evo:carb:enrichener_knob_mod_by_jrogers329.jpg?direct&300|}} ((photo by jrogers329 of the XLFORUM http://xlforum.net/forums/showthread.php?p=1283849#post1283849)) \\ | + | {{:techtalk:evo:carb:enrichener_knob_mod_by_jrogers329.jpg?direct&300|}} ((photo by jrogers329 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/30821-choke-knob#post1084456)) \\ |
| ====== Mooneyes Knob ====== | ====== Mooneyes Knob ====== | ||
| Line 24: | Line 25: | ||
| It takes a while but it will come off. Make sure to wear eye protection since the plastic will fly all over the garage when cutting on it. | It takes a while but it will come off. Make sure to wear eye protection since the plastic will fly all over the garage when cutting on it. | ||
| - | {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_1_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=46782)) {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_2_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=46782)) \\ | + | {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_1_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/28235-e-z-choke-knob-removal-new-knob-install?t=46782)) {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_2_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/28235-e-z-choke-knob-removal-new-knob-install?t=46782)) \\ |
| If the ID of the new knob is too small, you'll need to drill the hole out larger to go over the stud. \\ | If the ID of the new knob is too small, you'll need to drill the hole out larger to go over the stud. \\ | ||
| Line 35: | Line 36: | ||
| Then the knob was installed on the rod with thread sealer (nail polish in this instance) and the set screw tightened up. \\ | Then the knob was installed on the rod with thread sealer (nail polish in this instance) and the set screw tightened up. \\ | ||
| - | {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_3_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=46782)) {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_4_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=46782)) {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_5_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM http://xlforum.net/forums/showthread.php?t=46782)) \\ | + | {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_3_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/28235-e-z-choke-knob-removal-new-knob-install?t=46782)) {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_4_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/28235-e-z-choke-knob-removal-new-knob-install?t=46782)) {{:techtalk:evo:carb:mooneyes_deco_dash_knob_enrichenor_knob_5_by_johnny_wolf.jpg?direct&300|}} ((photo by Johnny Wolf of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/28235-e-z-choke-knob-removal-new-knob-install?t=46782)) \\ |
| \\ | \\ | ||
