Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:evo:carb03a [2019/04/09 20:38] hippysmack [Installing the Intake] |
techtalk:evo:carb03a [2019/08/28 22:53] hippysmack [Installing the Intake] |
||
---|---|---|---|
Line 5: | Line 5: | ||
===== Considerations ===== | ===== Considerations ===== | ||
+ | **Repairing a Bend Where the Carb Mounts**: \\ | ||
+ | |{{:techtalk:evo:carb:bent_intake_manifold_fix_1_by_matt_black.jpg?direct&300|}}|{{:techtalk:evo:carb:bent_intake_manifold_fix_2_by_matt_black.jpg?direct&300|}}|{{:techtalk:evo:carb:bent_intake_manifold_fix_3_by_matt_black.jpg?direct&300|}}| | ||
+ | |||
**Intake Mounting Bolts**: \\ | **Intake Mounting Bolts**: \\ | ||
Inspect the intake mounting bolts for distortion at the threads as well as the Allen socket in the head. \\ | Inspect the intake mounting bolts for distortion at the threads as well as the Allen socket in the head. \\ | ||
Line 43: | Line 46: | ||
|Install the intake with the slots toward the left side of the engine. \\ Leave the bolts loose until you install the carb. ((photos by Hippysmack))|| | |Install the intake with the slots toward the left side of the engine. \\ Leave the bolts loose until you install the carb. ((photos by Hippysmack))|| | ||
|{{:techtalk:evo:carb:intake_manifold_13_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:carb:intake_manifold_14_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:carb:intake_manifold_13_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:carb:intake_manifold_14_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | |{{:techtalk:evo:carb:intake_manifold_flange_alignment_1_by_matt_black.jpg?direct&200|}}|{{:techtalk:evo:carb:intake_manifold_flange_alignment_2_by_matt_black.jpg?direct&200|}}| | ||
Having the carb in place allows the carb seal and the manifold to squarely mate with the carb before tightening the intake bolts. ((John Harper of the XLFORUM http://xlforum.net/forums/showthread.php?t=2011585&highlight=intake+manifold&page=2)) \\ | Having the carb in place allows the carb seal and the manifold to squarely mate with the carb before tightening the intake bolts. ((John Harper of the XLFORUM http://xlforum.net/forums/showthread.php?t=2011585&highlight=intake+manifold&page=2)) \\ | ||
Line 64: | Line 69: | ||
* Install the carb in the intake, the air cleaner on the carb and install the carb support on the heads loosely. | * Install the carb in the intake, the air cleaner on the carb and install the carb support on the heads loosely. | ||
* Then wiggle the intake up/down and visually inspect the seal top to bottom for evenness. | * Then wiggle the intake up/down and visually inspect the seal top to bottom for evenness. | ||
- | * Torque the crab support bolts. | + | * Torque the carb support bolts. |
* Then torque the intake bolts. | * Then torque the intake bolts. | ||
* Recheck the seal for evenness. | * Recheck the seal for evenness. |