Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:evo:engmech02b [2019/02/28 20:51] hippysmack [Test Fit the Lifters] |
techtalk:evo:engmech02b [2019/02/28 22:15] hippysmack [Considerations Before You Begin] |
||
---|---|---|---|
Line 32: | Line 32: | ||
Notice how the left side of the pin touches the wall and the right side doesn't. \\ | Notice how the left side of the pin touches the wall and the right side doesn't. \\ | ||
The pin diameter is split between the lifter bore and the pushrod tube drain. \\ | The pin diameter is split between the lifter bore and the pushrod tube drain. \\ | ||
- | {{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_42_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | + | {{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_42_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:oil:91-99_lifter_pin_screw_upgrade_52_by_hippysmack.jpg?direct&400|}} ((drawing by Hippysmack)) |
Simplified drawings of the upgrade: \\ | Simplified drawings of the upgrade: \\ | ||
Line 175: | Line 175: | ||
|{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_49_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_50_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_49_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_50_by_hippysmack.jpg?direct&300|}}| | ||
- | |||
- | If a screw locks up a lifter when installed, the back hole did wander away from center. \\ | ||
- | The lifter below was moving fine with the bolt inserted and threaded to the head but not tightened. \\ | ||
- | It locked up as soon as the bolt was torqued to 10 in lbs. \\ | ||
- | Upon tightening, the bolt flexed in the middle as in the example diagram above against the lifter. \\ | ||
- | |||
- | |{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_36_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_37_by_hippysmack.jpg?direct&300|}}| | ||
You can use a feeler gauge between the pin and lifter flat. \\ | You can use a feeler gauge between the pin and lifter flat. \\ | ||
Line 188: | Line 181: | ||
The lifter below has app .001" clearance to the pin screw. \\ | The lifter below has app .001" clearance to the pin screw. \\ | ||
- | |{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_47_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_48_by_hippysmack.jpg?direct&300|}}| | + | |{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_47_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_48_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_51_by_hippysmack.jpg?direct&300|}}| |
+ | If a screw locks up a lifter when installed, the back hole did wander away from center. \\ | ||
+ | The lifter below was moving fine with the bolt inserted and threaded to the head but not tightened. \\ | ||
+ | It locked up as soon as the bolt was torqued to 10 in lbs. \\ | ||
+ | Upon tightening, the bolt flexed in the middle as in the example diagram above against the lifter. \\ | ||
+ | |{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_36_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:engmech:91-99_lifter_pin_screw_upgrade_37_by_hippysmack.jpg?direct&300|}}| | ||
====== If the lifters lock up ====== | ====== If the lifters lock up ====== | ||