Below are different cam chest pics showing the oil passages from the filter pad.

86 Cam Chest 1)

1995 Cam Chest 2)	1995 Cam Chest 3)

1998 Cam Chest 4)	1999 Cam Chest 5)	2000 Cam Chest 6)

2001 Cam Chest 7)	2003 Cam Chest 8)

2004 Cam Chest 9)	2005 Cam Chest 10)	2008 Cam Chest 11)

2013 Cam Chest 12)

XR1200 Cam Chest 13)

The lifter oil feed galley is a hole located along the top of the case between both intake tappets.

• The feed galley is responsible for carrying oil to the lifters.
• It gets it's oil from the cam cover.
  • A hole is internally routed from the top to the bottom of the cover with a hole exiting in a corresponding hole in the case.
  • The cam cover gets it's oil from the oil pump via intersecting holes between the bottom of the case and the cover.
  • Feed oil is routed inside the cover but not to the gearcase.
• The hole in the middle of the case at the top intersects into the internal oil feed galley.
• Cross drilled passages intersect the main feed galley and carry oil to each intake lifter.
  Exhaust lifters are fed oil (bore to bore) from a drilled passage into each one's respective intake lifter bore.
• This is the end point of static oil pump pressure to the top end.
  • The lifters supply oil pressure to the rocker boxes.

86-90 main oil feed path 14)

The main oil feed galley is a horizontal passage located along the top of the case beside the tappet blocks and lifters.
It runs from the filter pad to the last lifter bore (lifter for #1 cam).
This oil galley feeds the lifters, cam cover / pinion shaft / hole in pinion gear to the rod bearings and also the gears on cam #2.

• The feed galley is responsible for carrying oil into the engine.
• It gets it's oil from the filter / check ball.
• 91-99 engine feed galley is an internally drilled hole in the case.
  • It runs behind and into on both sides of the small cavity (small slot) milled into the outside edge of the case.
• 2000 and up engine feed galley is an external slot milled into the outside edge of the case.
  • The oil passage runs on the outside (right) of the lifter bores as in 91-99 cases with a hole drilled through it into each lifter bore.
• Cross drilled passages intersect the main feed galley and carry oil to each lifter from the feed galley.
  • This is the end point of static oil pump pressure to the top end.
  • The lifters supply oil pressure to the rocker boxes.
• A small amount of oil sprays down onto the rear intake (#2) cam gear through a tiny hole in the middle of the feed galley.
• The cam cover gets it's oil from an intersecting passage in the feed galley at the top of the cover.
  (the gearcase gets no oil from this passage in the cover, outside of spill from the pinion shaft bushing)

In examining the area directly behind the filter inside the gearcase;
You can see the oil path (channels from the filter to the engine).
There is a plug on the outside case in the area of the filter.
The plugged hole is from where the MoCo drilled the oil passage to connect the outlet of the oil filter to the lifters. ¹⁵⁾
After they drill it, they stick a plug in it.
There are other plugged holes like that on your motor where the drilling operation left a hole that had to be plugged.

On 91-99 engines, the oil feed galley is internal from the filter pad. Oil travels to each lifter individually from this cavity. 16)	Rifling hole for the feed galley is plugged outside the case near the filter. 17)

On 2000 and up engines, the oil feed galley is external. Oil travels to each lifter individually from this cavity. 18)	The rifling hole for the feed galley is plugged outside the case near the filter. 19)

• Pressurized oil in the pinion bushing is sent through a hole in the (hollow) pinion shaft toward the flywheel.
  • Oil travels to and through the right flywheel via an internal passage from the pinion bore and the crank pin bore in the flywheel.
    Oil enters the crank pin inside the crank pin bore on the flywheel.
  • Oil is routed out of the crank pin through a hole under the rod bearings in the middle of the pin and circulates to the rod bearings.
• This is the end point of static oil pump pressure to the bottom end.
• Oil leaving the rod bearings flows into the crankcase to be scavenged by the oil pump (or splashed into the gearcase).
• Crankcase pressure moves the oil from this point.

L81-03 'one hole' crank pin. 20)

• Oil flows off the pushrod side of the rocker boxes through the pushrod covers, into vertical holes in the lifter bores and into the gearcase.
  • Oil falls on the cam lobes on the way down this hole.
  • Some of this oil is transferred between the gear teeth.
• The rear intake (#2) cam gets a little oil spray from the right case oil feed galley through the small orifice underneath the open cavity in the case.
  • That oil is transferred between the teeth of the cams.
• Oil flung off the cams lands in the gearcase to be collected into the scavenge (return) side of the oil pump.

Below are pics of the restricted orifice underneath the oil feed galley in the case that shoots a small stream onto #2 cam.
#2 cam rotates counterclockwise and the oil is sprayed on the right side of the cam gear for extra cooling.

(L) 92-99 21), (R) 2000 Up 22) cam oiling hole from the feed galley

All cam bushings are fed from splash oil into channeled holes drilled behind the bushing faces.
#1, #3 and #4 cam bores have channels drilled from the top down into the back side of the bores.
The channel for #2 cam bore starts at the bottom and is drilled into the back side of the bore.
The pinion bushing (as well as the hole in the pinion shaft) is fed from a cross drilled hole in the top of the cover.

91 and up Sportster engines have an internal rifling hole drilled into the lower left side of the case running past the left side of the oil pump.
That extra hole (in the picture below) is benign and doesn't need a hole in the gasket to match.
That hole is purely an artifact of how they connected two passages for routing crankcase oil up to the oil pump's scavenge section.
They drill that hole to connect the two passages, and then it gets blocked off naturally by the cam box cover and gasket. ²³⁾

Also, in 2000, the factory changed the oil routing to the lifters to make manufacturing the cases easier.
The newer cam cover on the left in the pic below and has two extra grooves along the top.
These grooves let oil get to the lifters.
If you have an older style gasket, it will not have cutouts for the grooves and you won't get oil to the lifters.

Rubbermount Evo vs Rigid Evo Cam Cover Internals 24)

Both have been chopped on the outside but the gearcase perimeter is intact on them for reference.

91-99 cam cover gasket 25)	91-99 cam cover seals off the extra hole. 26)

2000-up cam cover gasket 27)	2000 up gasket seals off the extra hole. 28)

DON'T INSTALL a 91-99 CAM COVER GASKET ON A 2000-UP MOTOR!!!!!!!

The 91-99 cam cover gasket has no business being on a 2000+ motor at all. It will cause you to lose all oil pressure. ²⁹⁾
The 2000+ gasket supersedes the 91-99 gasket. In other words, it can be used all the way back to 1991.
Most companies completely dropped the 91-99 specific gasket and only offer the one that can be used from 1991-present.
Either James Gasket hasn't done that, or they may have some old stock.

The 91-99 lifter feed galley is an internal rifling hole in the case. It's drilled thru the case and only open to the cam cover via the center port to the pinion bushing.
The 2000-up lifter feed galley is external and it takes both the cover and the case mounted together to make up the feed galley.
So 00-up feed galley is split in half between the case and cover. The slots in the 2000-up cam cover gasket mate to both the case and the cover.
If you have the correct gasket on there, oil would be forced (between the cover and case) to all the lifter feed holes and piston squirters.
With the wrong gasket (91-99), oil pressure leaving the filter gets into that (now open) galley.
Then the oil will blow into into the cam chest, therefore bypassing the lifters, piston squirters and rod bearings.
The oil will simply cycle from the oil pump to cam chest to oil pump and back to the oil tank.
The oil light will stay off so you'll get no notice before moving the parts start oil starving and making noises and worse if the noises aren't heeded to quickly.

2000-up motor with 91-99 cam cover gasket. 30)	Below is a rough cross section of the joint in the feed galley at that first slotted run. 31)

³²⁾

• Gravity oil (drained from rocker boxes and head/cylinder drainage) falls on moving parts and into the crankcase.
  • Oil collected in the rocker box is returned to the crankcase through a passage in the cylinder and the head.
  • Oil collected in the push rod areas of the heads / rockers flows down the pushrod covers.
    • Then it flows down into the gearcase / cam chest through drain holes through in the tappet blocks.
    • Collected oil in the gearcase is routed to the crankshaft sump area via a low hole in the wall between them on the right side of the pinion shaft.
  • Excess oil mist drawn into the gearcase breather is separated from crankcase air pressure at the gearcase breather valve.
    • The separated oil (and condensed oil in the exit hose) flows into a drain hole below the breather valve and back into the gearcase.

Tappet blocks are directional (rear exhaust shown below).
^{33) 34)}

• Occasional excess pressured oil (from the oil filter pad) is dumped into the gearcase by the oil pressure relief valve.
  • High pressure oil, when cold (on startup), opens the pressure regulator.
  • The excess oil is dumped into the gearcase and routed to the sump area via the low hole in the wall between the gearcase and the crankcase.
• Splash oil in the sump area of the crankcase serves to lubricate the moving parts as well.

• Splash oil (from the up and down movement of the connecting rods, crankshaft and pressure generated under the pistons on downstroke) serves to lubricate;
• Cylinder walls
• Pistons, piston pins
• Cam gears and bushings
• Main bearings

86-90 engine sump splash holes 35)

• Drainage

86-90 oil scavenging 36)	86-90 cam cover 37)	86-90 Oil Pump Oiling Paths. 38)

^{39) 40)}

^{41) 42)}

• Gravity oil (drained from rocker boxes and head/cylinder drainage) falls on moving parts and into the crankcase.
  • (91 only) - Occasional excess pressured oil (from the oil filter pad) is dumped into the gearcase by the oil pressure relief valve.
    • 91 engines kept the oil pressure relief valve that opens at 30-35 psi and dumps oil into the gearcase.
    • The pressure relief was removed from future models.
  • 91-03
    • Oil collected in the rocker box is returned to the crankcase through a passage in each head and cylinder.
    • Oil collected in the push rod areas of the heads / rockers flows down the pushrod covers.
      • Then it flows down into the gearcase / cam chest through vertical drain holes in the tappet blocks.
    • Excess oil mist splashed into the rocker boxes is separated from crankcase air pressure at the breather baffles (plain umbrella valves).
      • The separated oil flows into drain holes in the rocker boxes and back into the crankcase.

Rocker box drainage 43)

91-03 breather holes in the rocker box sections and head 44)

91-03 style front head drainage hole 45)		Head drains in the cylinders 46)

91-03 style rear head drainage hole 47)		Head drains at the cylinder base on the case. 48)

• 04-Up
  • Oil collected in the rocker box is returned to the gearcase through a passage in the head and the right case.
  • Oil collected in the push rod areas of the heads / rockers flows down the pushrod covers.
    • Then it flows down into the gearcase / cam chest through vertical drain holes in the tappet blocks.
  • Excess oil mist splashed into the rocker boxes is separated from crankcase air pressure at the breather baffles (fancy umbrella valves).
    • The separated oil flows into drain holes in the rocker boxes and back into the gearcase.

Head drains in the cylinders 49) 1 hole is plugged on each cylinder during installation.	Head drains at the cylinder base on the case 50)

Milled slots in the left case match milled slots in the right case for rocker box drain from valve side. 51)	Lower part of slots in the right case exit thru drilled holes into the gearcase. 52)

Rocker box drains into the cam chest. 53)

• Splash oil
  (from the up and down movement of the connecting rods, crankshaft and pressure generated under the pistons on downstroke)
• Crankcase pressure mixed with oil in the sump area serves to splash (and lubricate) the moving parts such as;
  • Cylinder walls
  • Pistons, piston pins
  • Cam gears and bushings
  • Main bearings
• Crankcase pressure also serves to help 'push' oil from the sump into the scavenger port of the oil pump.

• The rubbermounts received an addition of piston oiler jets in the previous splash port locations.
• The holes in the cam chest wall from the inside no longer go through to the cam chest.
• Instead, the holes from the inside are passaged to the back of the lifter blocks where a drilled passage intersects into the oil feed galley. *
• Oil jets were installed there to direct feed oil up to the bottom of the pistons.
• The jets create a dual oil spray in a controlled direction upward to the pistons while crankcase pressure and out the ports in the wall for pressure venting.
• Pressurized air / oil mist leaves the crankcase through the bearing on the pinion shaft into the cam chest.
• There is no seal on the bearing and air pulses into the cam chest to be pulled up into vertical passages between the cam slots.

04-up piston jets. 58)		Piston jets from inside the case. 59)

See also the Evo Oil Pump section of the Sportsterpedia.

• Drainage
  • Oil collected in the crankcase sump is passage-routed to the scavenger side of the oil pump.
    (by pressure generated by the downward stroke of the pistons and the scavenging effect of the pump)
    Sump oil is collected by the pump at the 'ladle, half spoon, duck bill' protruding from the back of it where oil drops onto the scavenge gerotors.. ⁶⁰⁾
  • Oil collected in the gearcase / cam chest is routed to a drain port in the top of the oil pump where it drops down onto the scavenge gerotors.
  • Return oil fills a cavity above the pump's return gears from these dual inlets and pumps the oil back into the oil tank.

• Below is the case drain for a 98 engine. ⁶¹⁾
  • It's also a rifling hole drilled to connect the sump drain to the oil pump scavenge galley.
  • It could be plugged with a treaded pipe plug or a freeze plug.

Case drain / rifling hole for sump drain 62)	Rifling hole is on the back side of hole on the right. 63)

04 and up oil scavenge path 64)	04_up sump drain plug. 65)

98 and Up Oil Pump Oiling Paths 66)