Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:evo:susp03a [2019/12/06 16:33] hippysmack [Inspecting the Swingarm and Parts] |
techtalk:evo:susp03a [2020/06/13 07:28] hippysmack [Removing Bearing Races] |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ====== EVO: Suspension - Sub-03A ====== | ====== EVO: Suspension - Sub-03A ====== | ||
| - | ====== Rigid Mount Swingarm Bearing / Bushing Inspection and Replacement ====== | + | ====== 1998 1200S Swingarm Bearing / Bushing Inspection and Replacement ====== |
| \\ | \\ | ||
| ====== Prep Work ====== | ====== Prep Work ====== | ||
| Line 67: | Line 67: | ||
| {{:techtalk:evo:susp:swingarm_maintenance_22_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_23_by_hippysmack.jpg?direct&300|}} | {{:techtalk:evo:susp:swingarm_maintenance_22_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_23_by_hippysmack.jpg?direct&300|}} | ||
| {{:techtalk:evo:susp:swingarm_maintenance_24_by_hippysmack.jpg?direct&300|}} \\ | {{:techtalk:evo:susp:swingarm_maintenance_24_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | |||
| + | ====== Removing Bearing Races ====== | ||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_maintenance_25_by_hippysmack.jpg?direct&300|}} | ||
| + | {{:techtalk:evo:susp:swingarm_maintenance_26_by_hippysmack.jpg?direct&300|}} | ||
| + | {{:techtalk:evo:susp:swingarm_maintenance_27_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_maintenance_28_by_hippysmack.jpg?direct&300|}} | ||
| + | {{:techtalk:evo:susp:swingarm_maintenance_29_by_hippysmack.jpg?direct&300|}} | ||
| + | {{:techtalk:evo:susp:swingarm_maintenance_39_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_maintenance_30_by_hippysmack.jpg?direct&300|}} | ||
| + | {{:techtalk:evo:susp:swingarm_maintenance_32_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_maintenance_31_by_hippysmack.jpg?direct&300|}} | ||
| + | {{:techtalk:evo:susp:swingarm_maintenance_33_by_hippysmack.jpg?direct&300|}} | ||
| + | {{:techtalk:evo:susp:swingarm_maintenance_34_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_maintenance_35_by_hippysmack.jpg?direct&300|}} | ||
| + | {{:techtalk:evo:susp:swingarm_maintenance_36_by_hippysmack.jpg?direct&300|}} | ||
| + | {{:techtalk:evo:susp:swingarm_maintenance_37_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | |||
| + | ====== Removing Pivot Spacer Bushing ====== | ||
| + | |||
| + | The FSM says to replace this bushing only if needed. \\ | ||
| + | However, there is no criteria / spec to determine if it's needed. \\ | ||
| + | The bushing is pressed in and likewise will have to be pressed out. They make a special tool for removing / installing the bushing. \\ | ||
| + | The rig below can also be used as a remover / installer tool. \\ | ||
| + | |||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_bushing_remover-installer_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_bushing_remover-installer_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bushing_remover-installer_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bushing_remover-installer_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_bushing_remover-installer_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bushing_remover-installer_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bushing_remover-installer_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
