Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
techtalk:evo:susp03a [2020/06/16 16:02]
hippysmack [Installation]
techtalk:evo:susp03a [2020/06/16 23:13]
hippysmack [Bearing Outer Races]
Line 55: Line 55:
 From there you just push the other bearing out through the pivot. \\ From there you just push the other bearing out through the pivot. \\
 Hopefully your bearings won't look as bad as the ones below. You can spray them down with brake cleaner to clean off the old grease. \\ Hopefully your bearings won't look as bad as the ones below. You can spray them down with brake cleaner to clean off the old grease. \\
 +
 +After cleanup, these bearings sis not roll smooth (bumps felt while turning) so they had to be replaced. \\
  
 {{:​techtalk:​evo:​susp:​swingarm_maintenance_19_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_20_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_19_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_20_by_hippysmack.jpg?​direct&​300|}}
Line 67: Line 69:
 {{:​techtalk:​evo:​susp:​swingarm_maintenance_22_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_23_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_22_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_23_by_hippysmack.jpg?​direct&​300|}}
 {{:​techtalk:​evo:​susp:​swingarm_maintenance_24_by_hippysmack.jpg?​direct&​300|}} \\ {{:​techtalk:​evo:​susp:​swingarm_maintenance_24_by_hippysmack.jpg?​direct&​300|}} \\
 +
 +====== Installing the Swingarm and Parts ======
 +
 +If the internals are in good shape, wash down the bearings and internal parts with brake cleaner and dry with compressed air. \\
 +Old grease will contaminate the new grease. \\
 +Even if the bearings are new and came '​pre-greased',​ remove that with brake cleaner and add fresh grease. \\
 +
 +{{:​techtalk:​evo:​susp:​swingarm_maintenance_25_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_26_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_27_by_hippysmack.jpg?​direct&​300|}} \\
 +\\
 +
 +Packing bearings with grease in hand. The bearing spacer goes on the second bearing face before installation. \\
 +Install the bearings and spacer and cover them both with the dust shields. \\
 +
 +{{:​techtalk:​evo:​susp:​swingarm_maintenance_28_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_29_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_30_by_hippysmack.jpg?​direct&​300|}} \\
 +\\
 +
 +It's a good idea to install the pivot screw in the end of the pivot bolt before inserting it into the bearings (full of grease) to keep grease out of the threads. \\
 +Hold the swingarm in place, push the bolt thru and let it hang carefully while removing the screw from the left side. \\
 +Then remove the screw, install the spacer (chamfer out- towards frame), install the screw and torque to 50 ft/lbs.
 +Install everything else in reverse order. \\
 +
 +{{:​techtalk:​evo:​susp:​swingarm_maintenance_31_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_32_by_hippysmack.jpg?​direct&​300|}} \\
 +
 +{{:​techtalk:​evo:​susp:​swingarm_maintenance_33_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_34_by_hippysmack.jpg?​direct&​300|}} {{:​techtalk:​evo:​susp:​swingarm_maintenance_35_by_hippysmack.jpg?​direct&​300|}} \\
  
 ====== Bearing Outer Races ====== ====== Bearing Outer Races ======
 See also [[techtalk:​ref:​tools142#​swingarm_bushing_removal_installation|1982-2003 Swingarm Bushing Removal / Installation]] in the Tools section of the Sportsterpedia for several ideas on working with the races. \\ See also [[techtalk:​ref:​tools142#​swingarm_bushing_removal_installation|1982-2003 Swingarm Bushing Removal / Installation]] in the Tools section of the Sportsterpedia for several ideas on working with the races. \\
 +
 +Timken bearings and races come as a set and should be used as a set. \\
 +If bearings are in need of replacement,​ the races should also be removed and replaced with the ones that come with the new bearings. \\
 ===== Removal ===== ===== Removal =====
 A slide hammer was used to remove the outer races. \\ A slide hammer was used to remove the outer races. \\