Differences

This shows you the differences between two versions of the page.

--- techtalk:evo:susp03a [2020/06/16 16:01]
hippysmack [Removal]
+++ techtalk:evo:susp03a [2020/06/17 02:32] (current)
hippysmack [Inspecting the Swingarm and Parts]
@@ Line 46: / Line 46: @@
 Check that the swingarm isn't warped, damaged or rusted. \\
+{{:techtalk:evo:susp:swingarm_maintenance_36_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
 Remove the pivot bolt spacer and inspect both the spacer and it's bushing in the left pivot for damage or pitting. \\
@@ Line 55: / Line 58: @@
 From there you just push the other bearing out through the pivot. \\
 Hopefully your bearings won't look as bad as the ones below. You can spray them down with brake cleaner to clean off the old grease. \\
+After cleanup, these bearings did not roll smooth (bumps felt while turning) so they had to be replaced. \\
 {{:techtalk:evo:susp:swingarm_maintenance_19_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_20_by_hippysmack.jpg?direct&300|}}
@@ Line 67: / Line 72: @@
 {{:techtalk:evo:susp:swingarm_maintenance_22_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_23_by_hippysmack.jpg?direct&300|}}
 {{:techtalk:evo:susp:swingarm_maintenance_24_by_hippysmack.jpg?direct&300|}} \\
+====== Installing the Swingarm and Parts ======
+If the internals are in good shape, wash down the bearings and internal parts with brake cleaner and dry with compressed air. \\
+Old grease will contaminate the new grease. \\
+Even if the bearings are new and came 'pre-greased', remove that with brake cleaner and add fresh grease. \\
+{{:techtalk:evo:susp:swingarm_maintenance_25_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_26_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_27_by_hippysmack.jpg?direct&300|}} \\
+\\
+Packing bearings with grease in hand. The bearing spacer goes on the second bearing face before installation. \\
+Install the bearings and spacer and cover them both with the dust shields. \\
+{{:techtalk:evo:susp:swingarm_maintenance_28_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_29_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_30_by_hippysmack.jpg?direct&300|}} \\
+\\
+It's a good idea to install the pivot screw in the end of the pivot bolt before inserting it into the bearings (full of grease) to keep grease out of the threads. \\
+Hold the swingarm in place, push the bolt thru and let it hang carefully while removing the screw from the left side. \\
+Then remove the screw, install the spacer (chamfer out- towards frame), install the screw and torque to 50 ft/lbs.
+Install everything else in reverse order. \\
+{{:techtalk:evo:susp:swingarm_maintenance_31_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_32_by_hippysmack.jpg?direct&300|}} \\
+{{:techtalk:evo:susp:swingarm_maintenance_33_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_34_by_hippysmack.jpg?direct&300|}} {{:techtalk:evo:susp:swingarm_maintenance_35_by_hippysmack.jpg?direct&300|}} \\
 ====== Bearing Outer Races ======
 See also [[techtalk:ref:tools142#swingarm_bushing_removal_installation|1982-2003 Swingarm Bushing Removal / Installation]] in the Tools section of the Sportsterpedia for several ideas on working with the races. \\
+Timken bearings and races come as a set and should be used as a set. \\
+If bearings are in need of replacement, the races should also be removed and replaced with the ones that come with the new bearings. \\
 ===== Removal =====
 A slide hammer was used to remove the outer races. \\
@@ Line 83: / Line 115: @@
 The best tools ended up being a flat aluminum scrap piece and a hammer to 'set' the races in straight and a threaded rod and socket press to pull the races home. \\
 Just slight tapping was all that was required to get them started. \\
+The races will have a certain resistance when pressing them in. You'll feel the resistance and the races moving. \\
+If the resistance changes drastically (tightens suddenly), STOP, remove the tool and find out why. \\
 {{:techtalk:ref:tools:swingarm_bearing_race_installation_6_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:tools:swingarm_bearing_race_installation_7_by_hippysmack.jpg?direct&300|}} \\
@@ Line 148: / Line 183: @@
 But without having that tool, a socket was bolted up into the bearing bore sitting on top of the open end of the ring to keep it from popping out. \\
 Then the other side of the ring was carefully knocked into the bore with a wooden dowel and a hammer. \\
-Once the ring was fully in the bore, the socket was used to know the ring down so it snapped into the groove. ((photos by Hippysmack)) \\
+Once the ring was fully in the bore, the socket was used to push the ring down so it snapped into the groove. ((photos by Hippysmack)) \\
 {{:techtalk:ref:tools:swingarm_bearing_lockring_10_on_1998_xl1200s.jpg?direct&300|}} {{:techtalk:ref:tools:swingarm_bearing_lockring_11_on_1998_xl1200s.jpg?direct&300|}} {{:techtalk:ref:tools:swingarm_bearing_lockring_12_on_1998_xl1200s.jpg?direct&300|}} \\

Trace:

Differences

Navigation

Search

Toolbox