Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:evo:transfinal04 [2019/06/11 08:44] ixl2relax [Shifter Assembly] |
techtalk:evo:transfinal04 [2019/06/11 08:59] ixl2relax [Shifter Assembly] |
||
|---|---|---|---|
| Line 15: | Line 15: | ||
| **2004-2005 vs 2006+ Shifter Assembly**\\ | **2004-2005 vs 2006+ Shifter Assembly**\\ | ||
| - | Note the following part number differences between 04-05 and 06-later. The 06-later shifter shaft is larger than the previous version and therefore the hole in the primary cover is larger & the bushing & oil seal is different. | + | Note the following part number differences between 04-05 and 06-later. The 06-later shifter shaft is larger than\\ |
| + | the previous version and therefore the hole in the primary cover is larger & the bushing & oil seal is different. | ||
| ^ Part Description ^ 2004-05 P/N ^ 2006-2007 P/N ^ 2008-later P/N | | ^ Part Description ^ 2004-05 P/N ^ 2006-2007 P/N ^ 2008-later P/N | | ||
| Line 26: | Line 27: | ||
| | All of these may have the same Internal Casting # 34951-04 which can be confusing |||| | | All of these may have the same Internal Casting # 34951-04 which can be confusing |||| | ||
| - | +__06-later - The outer diameter of the seal is larger, the bushings have a shoulder and press in from the inside of the cover. ((oo_buck_us in Post#15 - http://xlforum.net/forums/showthread.php?t=1560232))\\ | + | +__06-later - The outer diameter of the seal is larger, the bushings have a shoulder and press in place from the inside of the cover. ((oo_buck_us in Post#15 - http://xlforum.net/forums/showthread.php?t=1560232))\\ |
| ++_latest P/N (orig P/N 37101-84)\\ | ++_latest P/N (orig P/N 37101-84)\\ | ||
| Line 32: | Line 33: | ||
| On all models: | On all models: | ||
| The oil seal can be removed without removing the primary cover - remove the lever, then use a pick or screwdriver to pry the seal out of the cavity. | The oil seal can be removed without removing the primary cover - remove the lever, then use a pick or screwdriver to pry the seal out of the cavity. | ||
| + | |||
| + | The Oil Seal is installed first, followed by the washer/spacer (NOTE that the parts manual for 2004 & 2005 shows the Rubber Washer installed first & then the Oil Seal - but this is **WRONG!**) | ||
| On installs, be sure to put tape over the splines on the shifter shaft before installing the oil seal to prevent the splines from cutting the seal. | On installs, be sure to put tape over the splines on the shifter shaft before installing the oil seal to prevent the splines from cutting the seal. | ||
| Line 39: | Line 42: | ||
| {{:techtalk:evo:transfinal:shiftershaft-tapeoversplines-manborn.jpg?335|}} | {{:techtalk:evo:transfinal:shiftershaft-tapeoversplines-manborn.jpg?335|}} | ||
| {{:techtalk:evo:transfinal:shiftershaft-oringmod-4pac.jpg?400|}} | {{:techtalk:evo:transfinal:shiftershaft-oringmod-4pac.jpg?400|}} | ||
| + | |||
| + | Some XLForum reference threads:\\ | ||
| + | http://xlforum.net/forums/showthread.php?t=254258\\ | ||
| + | http://xlforum.net/forums/showthread.php?t=79795\\ | ||
| + | http://xlforum.net/forums/showthread.php?t=1560232 (pics of '04 & '06 primary cover)\\ | ||
| + | http://xlforum.net/forums/showthread.php?t=548729\\ | ||
| + | http://xlforum.net/forums/showthread.php?t=1218730\\ | ||
| + | |||
| \\ | \\ | ||
