Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ih:oil01 [2019/03/13 21:43] hippysmack [Ironhead Engine breather 101 Through 1985] |
techtalk:ih:oil01 [2019/06/14 03:37] hippysmack [Rocker Box] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| ====== IH: Oiling & Lubrication ====== | ====== IH: Oiling & Lubrication ====== | ||
| + | ====== Engine Oiling ====== | ||
| + | |||
| ====== Oil Tank Pressure ====== | ====== Oil Tank Pressure ====== | ||
| See the full article, [[techtalk:ref:oil04#oil_tank_pressure|Oil Tank Pressure]], in the REF section of the Sportsterpedia. \\ | See the full article, [[techtalk:ref:oil04#oil_tank_pressure|Oil Tank Pressure]], in the REF section of the Sportsterpedia. \\ | ||
| Line 164: | Line 166: | ||
| ===== Checking Oil Pressure ===== | ===== Checking Oil Pressure ===== | ||
| See also [[techtalk:ref:oil15|Installing an Oil Pressure Gauge]] in the Sportsterpedia. \\ | See also [[techtalk:ref:oil15|Installing an Oil Pressure Gauge]] in the Sportsterpedia. \\ | ||
| + | |||
| + | When checking oil pressure, it's important to note that you are not testing pressure at a dead stop standpoint. \\ | ||
| + | The oil is flowing into the engine at the same time you are testing from a still test site. \\ | ||
| + | Likewise, the resulting pressure reading is a reflection of residual pressure while that pressure is being manipulated. \\ | ||
| + | (by oil flow as well as the current viscosity) \\ | ||
| According to the MoCo (FSMs), the oil pump is the prime testing point of oil pressure to the engine. \\ | According to the MoCo (FSMs), the oil pump is the prime testing point of oil pressure to the engine. \\ | ||
| Line 401: | Line 408: | ||
| |Oil path of 85 style cam cover ((photo by billeuze of the XLFORUM http://xlforum.net/forums/showthread.php?t=1103082))| | |Oil path of 85 style cam cover ((photo by billeuze of the XLFORUM http://xlforum.net/forums/showthread.php?t=1103082))| | ||
| |{{:techtalk:ih:oil:85_cam_cover_1_by_billeuze_annotated_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ih:oil:85_cam_cover_1_by_billeuze_annotated_by_hippysmack.jpg?direct&300|}}| | ||
| + | |||
| + | ===== Oil Lines to the Rockers ===== | ||
| + | |||
| + | |||
| + | ===== Rocker Box ===== | ||
| + | The feed to the rockers is not a large diameter passage and not a lot of oil goes to the rocker gear. ((Ferrous Head of the XLFORUM http://xlforum.net/forums/showthread.php?t=753175&highlight=split+rocker+box)) \\ | ||
| + | But if you pull the lines off with the engine running you should be getting a good steady flow out of them. \\ | ||
| ====== Bottom End Oiling ====== | ====== Bottom End Oiling ====== | ||
