Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ih:oil01 [2020/05/19 18:02] hippysmack [Oil Pump Check Valve] |
techtalk:ih:oil01 [2020/08/05 23:13] hippysmack [Oil Lines to the Rockers] |
||
---|---|---|---|
Line 133: | Line 133: | ||
====== Engine Oil Pressure (57-85) ====== | ====== Engine Oil Pressure (57-85) ====== | ||
See also [[techtalk:ref:oil04#sportster_oil_pressure_57_to_present|Sportster Oil Pressure (57 to Present)]] in the REF section of the Sportsterpedia. \\ | See also [[techtalk:ref:oil04#sportster_oil_pressure_57_to_present|Sportster Oil Pressure (57 to Present)]] in the REF section of the Sportsterpedia. \\ | ||
+ | |||
+ | On ironheads, 80% of oil pressure is sent to the bottom end and 20% is sent to the top end. ((2000 MMI Documents)) \\ | ||
The oil pump is non-regulatory and delivers its entire volume of oil under pressure to the oil filter mount. \\ | The oil pump is non-regulatory and delivers its entire volume of oil under pressure to the oil filter mount. \\ | ||
Line 413: | Line 415: | ||
| Oil line sleeves. ((photos by sc72 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1704463)) || | | Oil line sleeves. ((photos by sc72 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1704463)) || | ||
- | |{{:techtalk:ih:oil:83_model_oil_line_sleeves_1_by_sc72.jpg?direct&250|}}|{{:techtalk:ih:oil:83_model_oil_line_sleeves_1_by_sc72.jpg?direct&250|}}| | + | |{{:techtalk:ih:oil:83_model_oil_line_sleeves_1_by_sc72.jpg?direct&250|}}|{{:techtalk:ih:oil:83_model_oil_line_sleeves_2_by_sc72.jpg?direct&250|}}| |
===== Rocker Box ===== | ===== Rocker Box ===== | ||
The feed to the rockers is not a large diameter passage and not a lot of oil goes to the rocker gear. ((Ferrous Head of the XLFORUM http://xlforum.net/forums/showthread.php?t=753175&highlight=split+rocker+box)) \\ | The feed to the rockers is not a large diameter passage and not a lot of oil goes to the rocker gear. ((Ferrous Head of the XLFORUM http://xlforum.net/forums/showthread.php?t=753175&highlight=split+rocker+box)) \\ | ||
Line 422: | Line 424: | ||
====== Transfer Valve (76 and earlier) ====== | ====== Transfer Valve (76 and earlier) ====== | ||
- | The foregoing by Dr Dick ((http://xlforum.net/forums/showpost.php?p=3886388&postcount=40)) | + | |
+ | There is only one moving part in the transfer valve assembly which is the triangular shaped disc in the pics below (reed, patel, wafer or whatever you'd call it). \\ | ||
+ | It's a triangular piece of .009" thick stainless steel that can move about .015" left to right in the valve. There is no spring. \\ | ||
+ | In a RUNNING engine, it is a one way valve that lets air and oil pass through it from primary case to flywheel case. \\ | ||
+ | [[https://www.youtube.com/watch?v=EOu0uR2ulF8|Click here]] to see a video of the direction of flow. \\ | ||
+ | |||
+ | Positive crankcase pressure pushes the reed to the left and seals a small hole preventing flow into the primary. \\ | ||
+ | Vacuum in the crankcase pulls the reed to the right up against a stop that has a larger hole. \\ | ||
+ | The 3 cuts that make the reed a triangle allow air/oil to flow around it into the crankcase. \\ | ||
+ | |||
+ | Without the engine running and with no spring to maintain a tight seal, oil can slowly leak through and let wet sumped oil pass into the primary. \\ | ||
+ | On engine start up the excess oil in the primary should be transferred back into the engine. \\ | ||
+ | |||
+ | The thread is 3/4"-16. \\ There is nothing to wear out. However anything that stops the movement of the reed (rust or dirt) means the valve won't work. \\ | ||
+ | The one taken apart here was gummed up with old oil that had a tar like consistency. \\ | ||
+ | |||
+ | {{:techtalk:ih:oil:transfer_valve_exposed_pic_1_by_needspeed.jpg?direct&800|}} ((photo by needspeed of the XLFORUM http://xlforum.net/forums/showthread.php?t=2077280)) \\ | ||
+ | |||
+ | Also, as a test, a container of 20w-50 oil at room temperature was allowed to gravity drain from the transfer valve. \\ | ||
+ | It took 48 hours for 100 milliliters of oil to drip through the valve. \\ | ||
+ | |||
+ | {{:techtalk:ih:oil:transfer_valve_exposed_pic_3_by_needspeed.jpg?direct&300|}} ((photo by needspeed of the XLFORUM http://xlforum.net/forums/showthread.php?t=2077280)) \\ | ||
+ | |||
+ | Here are a few drawings detailing the assembly: \\ | ||
+ | |||
+ | {{:techtalk:ih:oil:transfer_valve_exposed_pic_2_by_needspeed.jpg?direct&500|}} ((drawing by needspeed of the XLFORUM http://xlforum.net/forums/showthread.php?t=2077280)) \\ | ||
+ | |||
+ | |||
+ | ---- | ||
+ | |||
+ | ...... The foregoing by Dr Dick ((http://xlforum.net/forums/showpost.php?p=3886388&postcount=40)) | ||
The transfer valve is staked into position. ((Ferrous Head of the XLFORUM http://xlforum.net/forums/showthread.php?t=581947&page=6)) \\ | The transfer valve is staked into position. ((Ferrous Head of the XLFORUM http://xlforum.net/forums/showthread.php?t=581947&page=6)) \\ |