Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ih:oil03f [2019/06/26 04:53] hippysmack [Check Spring] |
techtalk:ih:oil03f [2019/12/19 05:18] hippysmack [L1962-1971] |
||
---|---|---|---|
Line 5: | Line 5: | ||
* All these use 16t gear sets and style 1 plumbing ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | * All these use 16t gear sets and style 1 plumbing ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | ||
+ | * Gear Dia. (1.115" OD) | ||
+ | * Feed gears (.185" thick) | ||
* The production changes made during its run: ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | * The production changes made during its run: ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | ||
- | * 57-e58 baseline pump that all others came from. no oil seal. uses a snap ring and a full profile woodruff key at scavenge gear. | + | * 57-e58 baseline pump that all others came from. \\ No oil seal. \\ Uses a snap ring and a full profile woodruff key at scavenge gear. |
* L58-59 same as above but now has body machined for a oil seal. | * L58-59 same as above but now has body machined for a oil seal. | ||
- | * 60-e62 same as L58-59 but the retaining ring at the scavenge is replaced by half moon retainers. The scavenge drive gear is counter-bored for these half moons and the woodruff key is shortened so it won't interfere with the half moons. | + | * 60-e62 same as L58-59 but the retaining ring at the scavenge is replaced by half moon retainers. \\ The scavenge drive gear is counter-bored for these half moons and the woodruff key is shortened so it won't interfere with the half moons. |
===== L1962-1971 ===== | ===== L1962-1971 ===== | ||
* All these used 14t gears & scavenge sets got taller than the previous 16's were. ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | * All these used 14t gears & scavenge sets got taller than the previous 16's were. ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | ||
+ | * Gear Dia. (.990" OD) | ||
+ | * Feed gears (.216" thick) | ||
* All use half moons and shortened key on scavenge drive. | * All use half moons and shortened key on scavenge drive. | ||
* Bodies made till '66 are for style 1 plumbing. | * Bodies made till '66 are for style 1 plumbing. | ||
Line 22: | Line 26: | ||
* These go back to 16t gears and a snap ring with long key ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | * These go back to 16t gears and a snap ring with long key ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | ||
- | * Feed gears are the same as 57-e62 but the scavenge set is now wider again (wider than any of the previous sets). | + | * Gear Dia. (1.115" OD) |
+ | * Feed gears (.185" thick) | ||
+ | * Feed gears are the same as 57-e62 but the scavenge set is now wider again (wider than any of the previous sets). | ||
* Breather gear gets enlarged slots in it. ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | * Breather gear gets enlarged slots in it. ((Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204)) | ||
* Breather timing: | * Breather timing: |