Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ih:oil03f [2021/02/17 18:28] hippysmack [Oil Check Ball and Spring] |
techtalk:ih:oil03f [2021/06/26 05:53] hippysmack [1957-1967 Oil Pump Drive Gear] |
||
|---|---|---|---|
| Line 39: | Line 39: | ||
| | 52-E57 ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1661356&page=2)) | (L) L57-E72 - (R) L72-76 ((photo by fergerburger of the XLFORUM http://xlforum.net/forums/showthread.php?t=1661356)) | (Bottom) L57-E72 - (Top) L72-76 ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1661356)) | | | 52-E57 ((photo by Dr Dick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1661356&page=2)) | (L) L57-E72 - (R) L72-76 ((photo by fergerburger of the XLFORUM http://xlforum.net/forums/showthread.php?t=1661356)) | (Bottom) L57-E72 - (Top) L72-76 ((photo by The Doctor71 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1661356)) | | ||
| - | ====== Rear Feed Line Plug ====== | + | ====== Rear Feed Nipple or Plug ====== |
| Starting in 1967, the oil feed from the tank was plumbed directly into the oil pump on the rear side on XLH motors. \\ | Starting in 1967, the oil feed from the tank was plumbed directly into the oil pump on the rear side on XLH motors. \\ | ||
| The feed from the tank stayed plumbed to the top of the rear case on XLCH motors thru 1969. \\ | The feed from the tank stayed plumbed to the top of the rear case on XLCH motors thru 1969. \\ | ||
| - | In 1970, the feed on XLCH motors was now plumbed to the oil pump as well. \\ | + | In 1970, the feed on XLCH motors was now plumbed to the oil pump as well. The feed nipple (63533-41) is a 1/8"-27 x 3/8" Bose barb fitting. \\ |
| Using the same pump for both XLH and XLCH, this required a pipe plug installed there for XLCH motors from 1967-1969. \\ | Using the same pump for both XLH and XLCH, this required a pipe plug installed there for XLCH motors from 1967-1969. \\ | ||
| - | The plug is a 1/8"x27 NPT pipe plug. 2 part numbers were used and both are interchangeable. \\ | + | The plug is a 1/8"-27 NPT pipe plug. 2 part numbers were used and both are interchangeable. \\ |
| Part# (45831-48) used from 1967-1968 while part# (45830-48) used in 1969. \\ | Part# (45831-48) used from 1967-1968 while part# (45830-48) used in 1969. \\ | ||
| + | 1952-1956 K models also had a feed line plug there in the parts book part# (26424-52). \\ | ||
| + | | Oil pump on 1967 XLCH w/ feed plug ((photo by ss396 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1864035&page=4)) | | ||
| + | |{{:techtalk:ih:oil:1967_xlch_oil_pump_1_by_ss396.jpg?direct&300|}}| | ||
| ====== Breather Gears ====== | ====== Breather Gears ====== | ||
| Line 66: | Line 70: | ||
| |The 4 different scavenge gear sets. \\ Lined up from early in foreground to later in background. \\ This is to show the height progression.((photos by Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204))|Top view of all 4 sets.((photos by Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204))|A closer view of the height changes.((photos by Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204))| | |The 4 different scavenge gear sets. \\ Lined up from early in foreground to later in background. \\ This is to show the height progression.((photos by Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204))|Top view of all 4 sets.((photos by Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204))|A closer view of the height changes.((photos by Dr Dick of the XLFORUM http://xlforum.net/forums/showpost.php?p=3272806&postcount=204))| | ||
| |{{:techtalk:ih:oil:scavaenge_gear_sets_1_by_dr_dick.jpg?direct&220|}}|{{:techtalk:ih:oil:scavaenge_gear_sets_2_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:oil:scavaenge_gear_sets_3_by_dr_dick.jpg?direct&300|}}| | |{{:techtalk:ih:oil:scavaenge_gear_sets_1_by_dr_dick.jpg?direct&220|}}|{{:techtalk:ih:oil:scavaenge_gear_sets_2_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:oil:scavaenge_gear_sets_3_by_dr_dick.jpg?direct&300|}}| | ||
| + | |||
| \\ | \\ | ||
| [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
