Table of Contents
This is an old revision of the document!
IH: Suspension - Sub-03D
1957-1978 Swingarm Assembly and Installation
Swingarm Assembly
Orientation of Parts
Guide to Swingarm Bearing Replacement
Article and Pics by ericfreeman of the XLFORUM 2)
Click on a pic to enlarge:
Here are all the parts laid out as they will fit into the swingarm 3) → | The bearing outer races are already installed in the swingarm 4) | Inspect the swingarm inner surfaces to ensure they are clean. You can see the bearing outer race already installed in the other side. 5) |
Use some 800 wet/dry sandpaper to smooth the surface 6)→ | Press the outer races into place using an appropriate tool.7) | Grease the tapered roller bearing. I used a very sticky marine grease that won't wash out. It's not for bearings that rotate at high speed like wheel bearings but will be fine for the swingarm that just oscillates through a small arc. 8) |
Install the bearing in the outer race9)→ | Pack the area around the bearing with more grease and fit the spacer on the bearing, with the smaller diameter section facing up so it will fit into the hole in the dust cover.10) | Install the dust seal, ensuring it fits flush with the swingarm boss. The flat side of the spacer should protrude a little through the dust seal hole. This spacer will seat against the frame when the bearing preload is set.11) |
Here's the outer view of the leftside assembly, with the pivot bolt nut and bearing locknut in place. I'll wait to lock the bearing locknut into place until I trial-fit the swingarm to ensure I can properly adjust the left bearing preload.12)→ | Repeat the procedure on the other side. Here's what it looks like with both bearings installed.13) | This is the entire setup assembled to keep all the parts together prior to fitting the swingarm in the frame.14) |
Swingarm Installation
Bearing Preload
Comments from piniongear
After tightening the pivot bolt you should be able to obtain resistance by tightening the right side bearing lock nut.
Using a scale, tighten the lock nut to where it has 4-5 lbs resistance. 15)
Comments from Dr Dick 16)
Why preload? It makes sure the bearings aren't loose. How much preload? Too little makes your bike 'flighty'. It wont 'suretrack'. I call it 'marshmellow-ish'. Too much and you will burn thru bearings at an alarming rate. Where does the preload come from? Swingarm front casting flex.
Frame: A close look will show that both bearing inners and everything that slides over or attaches to the pivot bolt becomes solidified as one with the frame when the pivot bolt is tightened. They are immobile.
Swingarm: The 1-3/8“ hex adjuster forces the bearing outers into contact with the solidly located inners. This is possible because the outers aren't a tight press into the arm casting bores. Turning the 1-3/8” moves the outers closer to or farther from the non moving inners. These outers are part of the arm, not the frame.
So when the 1-3/8“ is loose, the arm is sloppy. You tighten the adjuster until all play just disappears. Now the outers have contacted the inners. The arm is not loose but it has no drag either.
If you hook a fish scale to the far end of the arm, it will weigh about 4lbs. If you raise the scale (and the arm) reading stays constant at 4lbs. Same happens as you lower scale. The reading stays at 4 lbs. Now you crank up 1/4 turn on the adjuster. What does this do? “well, that's a no brainer dick. it jams the bearing tighter”. Yes, but the bearings are very hard and they won't distort much from the pressure. Instead the arm front casting flexes open under the pressure. What ever the pressure applied to crunch the bearings, the same is forcing the casting flex open.
Now you put the scale on the arm. The scale won't get a solid reading of at-rest weight. If you raise the scale you now get 4-1/2 lbs and 3-1/2 as you lower. That's one half pound of drag. That drag is from the internal friction of the bearing, as it is under a 'pre'-load. Now you crank up another 1/8 turn on the adjuster. You now get 1 lb of drag (5 on upswing, 3 on drop, so far so good). You crank up the adjuster more looking for your two lbs. Funny thing happens. The drag isn't increasing as much. On 74-up bearings, you may not even get 2 lbs unless you tighten the Hell out of the adjuster? This is especially true for 78< arms. What's up with that?
You know what? The bearing is acting just as it should. It's carrying a larger load with out creating more friction. Isn't that what bearings are supposed to do? What I found out: The FSM says 1-2 lbs drag. But everyone just defaults to 2 lbs. At two lbs, the bearing life is dismal. At 1 lb, the bearings will last at least 3x longer. Does a tight preload control the arm better? Yes, at first. But it degrades as soon as the bearings get worn. And at 2 lbs, the bearings will wear to a point that is much worse than an unworn 1 lb'er rather quickly.
On any arm, the 73< bearing setup will control the arm better for any given preload and will outlast the 74> twice over.