Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:body20 [2018/11/07 21:57] hippysmack [Aftermarket Handlebars, Risers and Mods] |
techtalk:ref:body20 [2018/11/07 23:00] hippysmack [Offset Riser Blocks] |
||
---|---|---|---|
Line 10: | Line 10: | ||
|{{techtalk:ref:body:ape_hangers_by_brad_1.jpg?direct&200|}} {{techtalk:ref:body:ape_hangers_by_brad_2.jpg?direct&300|}}| | |{{techtalk:ref:body:ape_hangers_by_brad_1.jpg?direct&200|}} {{techtalk:ref:body:ape_hangers_by_brad_2.jpg?direct&300|}}| | ||
- | |1" Ape Hanger ((http://www.bikerparts-superstore.com/handlebars/ape-hangers/chrome-15-inch-ape-hangers-handlebar-for-1982-up-harley)) w/ stock risers on a 2005 XL883C - 33" wide, 15" total rise, 13" rise to grip tip, 14.5" pullback, 10" center width. ((photos courtesy of Brad of the XLFORUM))| | + | |1" Ape Hangers ((http://www.bikerparts-superstore.com/handlebars/ape-hangers/chrome-15-inch-ape-hangers-handlebar-for-1982-up-harley)) w/ stock risers on a 2005 XL883C \\ Dims: 33" wide, 15" total rise, 13" rise to grip tip, 14.5" pullback, 10" center width. ((photos courtesy of Brad of the XLFORUM))| |
|{{techtalk:ref:body:moto_bar_1_by_brad.jpg?direct&300|}} {{techtalk:ref:body:moto_bar_2_by_brad.jpg?direct&300|}}| | |{{techtalk:ref:body:moto_bar_1_by_brad.jpg?direct&300|}} {{techtalk:ref:body:moto_bar_2_by_brad.jpg?direct&300|}}| | ||
- | |1" (black) Moto Bar ((https://www.biltwellinc.com/p181/buy/parts-amp-accessories/handlebars/moto/-moto-handlebars-1-quot-black/#specs)) w/ stock risers and cables on a 2005 XL883 - 31" wide, 4.25" rise, 2.75" pullback, 4.75" center width. ((photos courtesy of Brad of the XLFORUM))| | + | |1" (black) Moto Bar ((https://www.biltwellinc.com/p181/buy/parts-amp-accessories/handlebars/moto/-moto-handlebars-1-quot-black/#specs)) w/ stock risers and cables on a 2005 XL883 \\ Dims: 31" wide, 4.25" rise, 2.75" pullback, 4.75" center width. ((photos courtesy of Brad of the XLFORUM))| |
====== Risers ====== | ====== Risers ====== | ||
===== Riser Mods ===== | ===== Riser Mods ===== | ||
+ | ==== Spacers ==== | ||
+ | |||
|Done on a 2005 1200R \\ Using 3/4" sockets: a 1/2"x13 nut (3/4" hex) was epoxied in each socket. The threads were then drilled out to 1/2". ((photos by thunderpaw of the XLFORUM http://xlforum.net/forums/showthread.php?postid=1239036))||| | |Done on a 2005 1200R \\ Using 3/4" sockets: a 1/2"x13 nut (3/4" hex) was epoxied in each socket. The threads were then drilled out to 1/2". ((photos by thunderpaw of the XLFORUM http://xlforum.net/forums/showthread.php?postid=1239036))||| | ||
|{{:techtalk:ref:body:riser_extensions_4_by_thunderpaw.jpg?direct&300|}}|{{:techtalk:ref:body:riser_extensions_2_by_thunderpaw.jpg?direct&300|}}|{{:techtalk:ref:body:riser_extensions_3_by_thunderpaw.jpg?direct&300|}}| | |{{:techtalk:ref:body:riser_extensions_4_by_thunderpaw.jpg?direct&300|}}|{{:techtalk:ref:body:riser_extensions_2_by_thunderpaw.jpg?direct&300|}}|{{:techtalk:ref:body:riser_extensions_3_by_thunderpaw.jpg?direct&300|}}| | ||
+ | ==== Offset Riser Blocks ==== | ||
+ | {{:techtalk:ref:body:offset_riser_mod_7_by_tobiism.jpg?direct&300|}} ((photo by tobiism of the XLFORUM http://xlforum.net/forums/showthread.php?t=906049&page=23)) | ||
+ | |||
+ | |Start with some square stock aluminum, drill holes for the bars (7/8" / 1" etc.) and mark center on the outside edge to cut a pinch slot. ((photos by tobiism of the XLFORUM http://xlforum.net/forums/showthread.php?t=906049&page=22))||| | ||
+ | |{{:techtalk:ref:body:offset_riser_mod_1_by_tobiism.jpg?direct&300|}}|{{:techtalk:ref:body:offset_riser_mod_2_by_tobiism.jpg?direct&300|}}|{{:techtalk:ref:body:offset_riser_mod_3_by_tobiism.jpg?direct&300|}}| | ||
+ | |The pinch slot can be cut with a hacksaw. \\ Drill the hole for the pinch bolt, countersink that for a cap head bolt. \\ Drill and countersink the second hole for the mounting bolt to the upper tree. ((photos by tobiism of the XLFORUM http://xlforum.net/forums/showthread.php?t=906049&page=22))||| | ||
+ | |{{:techtalk:ref:body:offset_riser_mod_4_by_tobiism.jpg?direct&300|}}|{{:techtalk:ref:body:offset_riser_mod_5_by_tobiism.jpg?direct&300|}}|{{:techtalk:ref:body:offset_riser_mod_6_by_tobiism.jpg?direct&300|}}| | ||