Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:body20 [2018/11/07 22:12] hippysmack [Handlebars] |
techtalk:ref:body20 [2018/11/07 23:00] hippysmack [Offset Riser Blocks] |
||
---|---|---|---|
Line 18: | Line 18: | ||
====== Risers ====== | ====== Risers ====== | ||
===== Riser Mods ===== | ===== Riser Mods ===== | ||
+ | ==== Spacers ==== | ||
+ | |||
|Done on a 2005 1200R \\ Using 3/4" sockets: a 1/2"x13 nut (3/4" hex) was epoxied in each socket. The threads were then drilled out to 1/2". ((photos by thunderpaw of the XLFORUM http://xlforum.net/forums/showthread.php?postid=1239036))||| | |Done on a 2005 1200R \\ Using 3/4" sockets: a 1/2"x13 nut (3/4" hex) was epoxied in each socket. The threads were then drilled out to 1/2". ((photos by thunderpaw of the XLFORUM http://xlforum.net/forums/showthread.php?postid=1239036))||| | ||
|{{:techtalk:ref:body:riser_extensions_4_by_thunderpaw.jpg?direct&300|}}|{{:techtalk:ref:body:riser_extensions_2_by_thunderpaw.jpg?direct&300|}}|{{:techtalk:ref:body:riser_extensions_3_by_thunderpaw.jpg?direct&300|}}| | |{{:techtalk:ref:body:riser_extensions_4_by_thunderpaw.jpg?direct&300|}}|{{:techtalk:ref:body:riser_extensions_2_by_thunderpaw.jpg?direct&300|}}|{{:techtalk:ref:body:riser_extensions_3_by_thunderpaw.jpg?direct&300|}}| | ||
+ | ==== Offset Riser Blocks ==== | ||
+ | {{:techtalk:ref:body:offset_riser_mod_7_by_tobiism.jpg?direct&300|}} ((photo by tobiism of the XLFORUM http://xlforum.net/forums/showthread.php?t=906049&page=23)) | ||
+ | |||
+ | |Start with some square stock aluminum, drill holes for the bars (7/8" / 1" etc.) and mark center on the outside edge to cut a pinch slot. ((photos by tobiism of the XLFORUM http://xlforum.net/forums/showthread.php?t=906049&page=22))||| | ||
+ | |{{:techtalk:ref:body:offset_riser_mod_1_by_tobiism.jpg?direct&300|}}|{{:techtalk:ref:body:offset_riser_mod_2_by_tobiism.jpg?direct&300|}}|{{:techtalk:ref:body:offset_riser_mod_3_by_tobiism.jpg?direct&300|}}| | ||
+ | |The pinch slot can be cut with a hacksaw. \\ Drill the hole for the pinch bolt, countersink that for a cap head bolt. \\ Drill and countersink the second hole for the mounting bolt to the upper tree. ((photos by tobiism of the XLFORUM http://xlforum.net/forums/showthread.php?t=906049&page=22))||| | ||
+ | |{{:techtalk:ref:body:offset_riser_mod_4_by_tobiism.jpg?direct&300|}}|{{:techtalk:ref:body:offset_riser_mod_5_by_tobiism.jpg?direct&300|}}|{{:techtalk:ref:body:offset_riser_mod_6_by_tobiism.jpg?direct&300|}}| | ||