Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:carb04 [2019/03/26 01:25] hippysmack [Pics of Lollipops Installed] |
techtalk:ref:carb04 [2019/04/28 02:30] hippysmack [Patriot Defender] |
||
---|---|---|---|
Line 298: | Line 298: | ||
====== Patriot Defender ====== | ====== Patriot Defender ====== | ||
+ | Dims: ((rocketmangb of the XLFORUM http://xlforum.net/forums/showthread.php?p=5737508)) \\ | ||
+ | 1-3/4" diameter out of the heads. \\ | ||
+ | Out to 2". \\ | ||
+ | Then 2-1/4" to the collector. \\ | ||
+ | The collector is probably 2-1/2" in a megaphone configuration. \\ | ||
+ | |||
+ | | Patriot Defender Pipes Pics and Dims. ((photos by rocketmangb of the XLFORUM http://xlforum.net/forums/showthread.php?p=5737508)) ||| | ||
|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_1_by_rocketmangb.jpg?direct&300|}}|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_2_by_rocketmangb.jpg?direct&300|}}|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_3_by_rocketmangb.jpg?direct&300|}}| | |{{:techtalk:ref:carb:patriot_defender_pics_and_dims_1_by_rocketmangb.jpg?direct&300|}}|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_2_by_rocketmangb.jpg?direct&300|}}|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_3_by_rocketmangb.jpg?direct&300|}}| | ||
+ | | Patriot Defender Pipes Pics and Dims. ((photos by rocketmangb of the XLFORUM http://xlforum.net/forums/showthread.php?p=5737508)) ||| | ||
|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_4_by_rocketmangb.jpg?direct&300|}}|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_5_by_rocketmangb.jpg?direct&300|}}|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_6_by_rocketmangb.jpg?direct&300|}}| | |{{:techtalk:ref:carb:patriot_defender_pics_and_dims_4_by_rocketmangb.jpg?direct&300|}}|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_5_by_rocketmangb.jpg?direct&300|}}|{{:techtalk:ref:carb:patriot_defender_pics_and_dims_6_by_rocketmangb.jpg?direct&300|}}| | ||
[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
+ | |||
+ | ====== Exhaust Bracket Mods ====== | ||
+ | Exhaust brackets can be fabricated to fit just about any configuration needed. \\ | ||
+ | (especially when using aftermarket pipes) \\ | ||
+ | |||
+ | Mount the pipes to the heads with proper torque. \\ Allow them to **gently** sit on their own. \\ | ||
+ | This allows for vertical and horizontal measurements to be taken from the point where the mount mates to the pipes. \\ | ||
+ | |||
+ | Below is the bracket that comes with the purchase of a set of Thunderheaders. \\ | ||
+ | This particular bracket was slightly too low and recessed to fit on a 98 1250. \\ | ||
+ | (it may have been fine for stock 1200 heads) \\ | ||
+ | The plate on the bracket was cut into and another plate was welded to it to extend the mounting holes. \\ | ||
+ | With the extra plate simply welded on top of the original one, the height worked out as well. \\ | ||
+ | |||
+ | | Thunderheader bracket mod. ((photos by Hippysmack)) ||| | ||
+ | |{{:techtalk:ref:carb:thunderheader_bracket_mod_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:carb:thunderheader_bracket_mod_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:carb:thunderheader_bracket_mod_1_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
\\ | \\ | ||