Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:ref:carb06 [2021/01/21 14:52] ixl2relax [Big Sucker w/External Breather] |
techtalk:ref:carb06 [2024/01/11 23:22] (current) hippysmack |
||
---|---|---|---|
Line 9: | Line 9: | ||
See also [[techtalk:ref:engmech05#breather_vent_relocation|Breather Vent Relocation]] in the REF section of the Sportsterpedia. \\ | See also [[techtalk:ref:engmech05#breather_vent_relocation|Breather Vent Relocation]] in the REF section of the Sportsterpedia. \\ | ||
- | Some air cleaners are not set up to allow for the breather bolts into them and are only held on by the small front bolts. ((Shu of the XLFORUM http://xlforum.net/forums/showthread.php?t=146084&page=11)) \\ | + | Some air cleaners are not set up to allow for the breather bolts into them and are only held on by the small front bolts. ((Shu of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/44522-show-me-your-non-stock-breather-systems/page11?t=146084&page=11)) \\ |
For these breathers you would need to get a head breather kit and carb support bracket. \\ | For these breathers you would need to get a head breather kit and carb support bracket. \\ | ||
The breather kit routes the head vents to the ground (or atmosphere) while the carb support bracket keeps the carb in the intake. \\ | The breather kit routes the head vents to the ground (or atmosphere) while the carb support bracket keeps the carb in the intake. \\ | ||
\\ | \\ | ||
- | Below is a breather vent re-direction on an EFI model. ((jcmellis of the XLFORUM http://xlforum.net/forums/showthread.php?t=1179974)) \\ | + | Below is a breather vent re-direction on an EFI model. ((jcmellis of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/120790-oil-drip-from-air-cleaner-fixed?t=1179974)) \\ |
A small amount of crankcase oil was dripping into the A/C on a Figure Machine/Engineering air cleaner assembly. \\ | A small amount of crankcase oil was dripping into the A/C on a Figure Machine/Engineering air cleaner assembly. \\ | ||
This air cleaner uses the stock Harley-Davidson breather tubes. \\ | This air cleaner uses the stock Harley-Davidson breather tubes. \\ | ||
Line 33: | Line 33: | ||
Once trimmed to size, the hoses are positioned at the mouth of the throttle body. \\ | Once trimmed to size, the hoses are positioned at the mouth of the throttle body. \\ | ||
- | {{:techtalk:ref:carb:hd_breather_mod_1_by_jcmellis.jpg?direct&300|}} ((photo by jcmellis of the XLFORUM http://xlforum.net/forums/showthread.php?t=1179974)) {{:techtalk:ref:carb:hd_breather_mod_2_by_jcmellis.jpg?direct&300|}} ((photo by jcmellis of the XLFORUM http://xlforum.net/forums/showthread.php?t=1179974)) | + | {{:techtalk:ref:carb:hd_breather_mod_1_by_jcmellis.jpg?direct&300|}} ((photo by jcmellis of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/120790-oil-drip-from-air-cleaner-fixed?t=1179974)) {{:techtalk:ref:carb:hd_breather_mod_2_by_jcmellis.jpg?direct&300|}} ((photo by jcmellis of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/120790-oil-drip-from-air-cleaner-fixed?t=1179974)) |
===== Big Sucker w/External Breather ===== | ===== Big Sucker w/External Breather ===== | ||
- | |||
{{:techtalk:ref:carb:bigsucker-extbreathermod-dodgenbullets.jpg?600|}} | {{:techtalk:ref:carb:bigsucker-extbreathermod-dodgenbullets.jpg?600|}} | ||
**How to modify the Big Sucker to vent to the atmosphere.**\\ | **How to modify the Big Sucker to vent to the atmosphere.**\\ | ||
- | http://xlforum.net/forums/showthread.php?t=34956 (There are a number of mods listed in this thread)\\ | + | https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/21180-poll-big-sucker-owners-plz-respond (There are a number of mods listed in this thread)\\ |
Commentary Posted by Dodgenbullets (See Post #17 & #19)\\ | Commentary Posted by Dodgenbullets (See Post #17 & #19)\\ | ||
Line 65: | Line 64: | ||
A variety of air filters and covers can now be used. . I interchange between a round cover and the "Ham Can" while using an over sized K&N filter. To bolt up the stock "Ham Can", take the bracket off the factory element and simply put it on the BS filter. Also, you can buy a replacement filter for the stage 2 Big Sucker and put it in your stage 1 kit. The filter element is the only difference in the stage 1 and 2. There's one replacement filter for all stage 2 applications. 3 holes match the CV 40, the others plug off. Now go try. | A variety of air filters and covers can now be used. . I interchange between a round cover and the "Ham Can" while using an over sized K&N filter. To bolt up the stock "Ham Can", take the bracket off the factory element and simply put it on the BS filter. Also, you can buy a replacement filter for the stage 2 Big Sucker and put it in your stage 1 kit. The filter element is the only difference in the stage 1 and 2. There's one replacement filter for all stage 2 applications. 3 holes match the CV 40, the others plug off. Now go try. | ||
- | + | \\ | |
- | + | ||
====== Running the Breather Hoses (91 and UP) ====== | ====== Running the Breather Hoses (91 and UP) ====== | ||
Line 88: | Line 85: | ||
===== Vent Line Routing ===== | ===== Vent Line Routing ===== | ||
==== Above vs Below the Head Vents ==== | ==== Above vs Below the Head Vents ==== | ||
- | |||
There has been debatable ways to route the vent lines off the heads when doing air cleaner mods. \\ | There has been debatable ways to route the vent lines off the heads when doing air cleaner mods. \\ | ||
However, exact line routing comes down to function over fashion. \\ | However, exact line routing comes down to function over fashion. \\ | ||
Line 114: | Line 110: | ||
Vent lines mounted low allows oil to leave the heads. \\ | Vent lines mounted low allows oil to leave the heads. \\ | ||
- | {{:techtalk:ref:carb:breather_lines_mounted_low_by_ixl2relax.jpg?direct&300|}} ((photo by IXL2Relax of the XLFORUM http://xlforum.net/forums/showthread.php?t=1051311&page=46)) {{:techtalk:ref:carb:breather_lines_mounted_low_by_beuz.jpg?direct&300|}} ((photo by beuz of the XLFORUM http://xlforum.net/forums/showthread.php?t=11697&page=582)) | + | {{:techtalk:ref:carb:breather_lines_mounted_low_by_ixl2relax.jpg?direct&300|}} ((photo by IXL2Relax of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/111555-air-cleaner-porn/page46?t=1051311&page=46)) {{:techtalk:ref:carb:breather_lines_mounted_low_by_beuz.jpg?direct&300|}} ((photo by beuz of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-styles/chopper-bobber-talk/7694-sporty-bobber-pictures/page582?t=11697&page=582)) |
Vent lines mounted high tend to promote a mixture of oil and condensation settling near the head connection of the hose. \\ | Vent lines mounted high tend to promote a mixture of oil and condensation settling near the head connection of the hose. \\ | ||
- | {{techtalk:ref:engmech:kuryakyn_breather_bolts_1_by_scar55.jpg?direct&300|}} ((photo by Scar55 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1690623)) {{techtalk:ref:engmech:kuryakyn_breather_bolts_2_by_scar55.jpg?direct&300|}} ((photo by Scar55 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1690623)) | + | {{techtalk:ref:engmech:kuryakyn_breather_bolts_1_by_scar55.jpg?direct&300|}} ((photo by Scar55 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/157991-ooozzz-running-out-of-my-crank-case-breather-hose?t=1690623)) {{techtalk:ref:engmech:kuryakyn_breather_bolts_2_by_scar55.jpg?direct&300|}} ((photo by Scar55 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-intake-and-exhaust/sportster-motorcycle-air-intake-carburetor-efi-fuel-and-exhaust/157991-ooozzz-running-out-of-my-crank-case-breather-hose?t=1690623)) |
====== Breather Bolts ====== | ====== Breather Bolts ====== | ||
Kuryakyn banjo bolts: \\ | Kuryakyn banjo bolts: \\ | ||
- | {{techtalk:ref:engmech:kuryakyn_banjo_breather_bolts_1_by_mick42.jpg?direct&300|}} ((photo by mick42 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2074032&page=2)) {{techtalk:ref:engmech:kuryakyn_banjo_breather_bolts_2_by_mick42.jpg?direct&300|}} ((photo by mick42 of the XLFORUM http://xlforum.net/forums/showthread.php?t=2074032&page=2)) | + | {{techtalk:ref:engmech:kuryakyn_banjo_breather_bolts_1_by_mick42.jpg?direct&300|}} ((photo by mick42 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/frame-mount-evo-sportster-talk-1986-2003-models/197402-pcv-valve-in-sporty-rocker-covers/page2?t=2074032&page=2)) {{techtalk:ref:engmech:kuryakyn_banjo_breather_bolts_2_by_mick42.jpg?direct&300|}} ((photo by mick42 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/frame-mount-evo-sportster-talk-1986-2003-models/197402-pcv-valve-in-sporty-rocker-covers/page2?t=2074032&page=2)) |
- | + | ||
====== Pics of Air Cleaners ====== | ====== Pics of Air Cleaners ====== | ||
- | | Caddy Ornament. ((photos by Lone Rider of the XLFORUM http://xlforum.net/forums/showthread.php?p=5712103&highlight=heel+toe#post5712103)) || | + | | Caddy Ornament. ((photos by Lone Rider of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-accessories/195309-those-little-ways-to-personalize-your-bike?highlight=heel+toe#post4250879)) || |
|{{:techtalk:ref:carb:caddy_ornament_ac_1_by_lone_rider.jpg?direct&300|}}|{{:techtalk:ref:carb:caddy_ornament_ac_2_by_lone_rider.jpg?direct&300|}}| | |{{:techtalk:ref:carb:caddy_ornament_ac_1_by_lone_rider.jpg?direct&300|}}|{{:techtalk:ref:carb:caddy_ornament_ac_2_by_lone_rider.jpg?direct&300|}}| | ||
- | |||
- | |||
- | |||
\\ | \\ |