Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:carb07 [2019/10/14 23:31] hippysmack [Andrews High Flow Accelerator Pump (Keihin butterfly)] |
techtalk:ref:carb07 [2019/10/14 23:58] hippysmack |
||
|---|---|---|---|
| Line 22: | Line 22: | ||
| Then pry the plug out using a pick or you could twist a small sheet metal screw into the hole to pull the plug out. \\ | Then pry the plug out using a pick or you could twist a small sheet metal screw into the hole to pull the plug out. \\ | ||
| With the plug removed clean the area around the mixture screw so no metal fragments remain. \\ | With the plug removed clean the area around the mixture screw so no metal fragments remain. \\ | ||
| - | {{techtalk:evo:carb:cv40-imscap-drillbit.jpg?300|}} ((photo by cantolina of the XLFORUM http://xlforum.net/forums/showthread.php?t=14949)) Circled area is where you drill out the plug. {{:techtalk:ref:carb:cv_carb_bottom_by_cantolina.jpg?direct&300|}} ((photo by cantolina of the XLFORUM http://xlforum.net/forums/showthread.php?t=14949)) | + | {{techtalk:evo:carb:cv40-imscap-drillbit.jpg?300|}} ((photo by cantolina of the XLFORUM http://xlforum.net/forums/showthread.php?t=14949)) Circled area is where you drill out the plug. {{:techtalk:ref:carb:idle_mixture_screw_location_by_popgadget-_annotated.jpg?direct&300|}} ((photo by popgadget of the XLFORUM, annotated by Hippysmack)) \\ |
| The EZ-Just mixture screw must be threaded in completely (lightly seated) prior to backing out and making final adjustments. \\ | The EZ-Just mixture screw must be threaded in completely (lightly seated) prior to backing out and making final adjustments. \\ | ||
| Line 51: | Line 51: | ||
| |{{:techtalk:ref:carb:ez-just_88-06_a-f_mixture_screw_1_by_hippysmack.jpg?direct&300|}} ((photo byHippysmack))| {{:techtalk:ref:carb:ez-just_88-06_a-f_mixture_screw_2_by_hippysmack.jpg?direct&300|}} ((photo byHippysmack))|{{:techtalk:ref:carb:ez-just_88-06_a-f_mixture_screw_3_by_hippysmack.jpg?direct&300|}} ((photo byHippysmack))| | |{{:techtalk:ref:carb:ez-just_88-06_a-f_mixture_screw_1_by_hippysmack.jpg?direct&300|}} ((photo byHippysmack))| {{:techtalk:ref:carb:ez-just_88-06_a-f_mixture_screw_2_by_hippysmack.jpg?direct&300|}} ((photo byHippysmack))|{{:techtalk:ref:carb:ez-just_88-06_a-f_mixture_screw_3_by_hippysmack.jpg?direct&300|}} ((photo byHippysmack))| | ||
| - | ===== EZ-Just Thumbscrew Mods ===== | + | ===== Idle Mixture Thumbscrew Mods ===== |
| Several mods to the thumbscrew have been done to make counting turns while turning the screw easier. \\ | Several mods to the thumbscrew have been done to make counting turns while turning the screw easier. \\ | ||
