Differences

This shows you the differences between two versions of the page.

--- techtalk:ref:carb07 [2019/10/14 23:31]
hippysmack [Andrews High Flow Accelerator Pump (Keihin butterfly)]
+++ techtalk:ref:carb07 [2021/08/09 01:32]
ixl2relax
@@ Line 4: / Line 4: @@
 \\
-====== Extended Idle Speed Screw ======
+====== Idle Speed Screw ======
+**CVP Extended Idle Speed Screw**\\
 Below is a CVP stainless steel idle speed screw for Harley CV and Keihin butterfly style carburetors. \\
 With the extended thumbscrew, idle speed can be adjusted by hand. \\
@@ Line 13: / Line 15: @@
 |{{:techtalk:ref:carb:cv_carb_with_extended_idle_speed_screw_by_hippysmack.jpg?direct&300|}}|
-====== Aftermarket Idle Mixture Screws and Mods ======
+**Modding a Factory Idle Speed Screw**\\
+You can stick a dime in the adjuster screw slot and braze it to the screw to make future adjustments by hand. \\
+{{:techtalk:ref:carb:keihin_carb_1_by_ddddylan_-_annotated.jpg?direct&300|}} ((photo by DDDDylan of the XLFORUM, annotated by Hippysmack))
+\\
+====== Idle Mixture Screw - IMS - Aftermarket & Mods ======
 \\
-===== EZ-Just Mixture Screws =====
+**CVP EZ-Just IMS**\\
 The EZ-Just mixture screw (for L76-87 or 88-06 models) ((https://cv-performance.com/ez-just-mixture-screw-81-87-harley-keihin)) ) can be purchased with an extended screw head for hand tuning. \\ You can buy packing from CVP also in case yours has been damaged or is not functioning properly. \\ But, check your local regulations before changing this out to an aftermarket part. \\ You can also find, buy or barter for used parts. \\ ("Please note: it is a violation of federal law to tamper with or disable any emission or noise control device. That is your PSA for the day"). ((XLForum member - chrishajer)) \\
@@ Line 35: / Line 44: @@
 {{:techtalk:ref:carb:ez_just_idle_mixture_screw_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\
-===== 88-06 =====
+**CVP EZ-Just IMS Used on 1988-06 CV40 Carbs**
 This screw is billed as "Easily tune and adjust your idle mixture without burning your hands or fumbling with a screwdriver." ((https://cv-performance.com/ez-just-mixture-screw)) \\
 This is not entirely true as you have to get your hand between the exhaust and air cleaner. \\
@@ Line 51: / Line 60: @@
 |{{:techtalk:ref:carb:ez-just_88-06_a-f_mixture_screw_1_by_hippysmack.jpg?direct&300|}} ((photo byHippysmack))| {{:techtalk:ref:carb:ez-just_88-06_a-f_mixture_screw_2_by_hippysmack.jpg?direct&300|}} ((photo byHippysmack))|{{:techtalk:ref:carb:ez-just_88-06_a-f_mixture_screw_3_by_hippysmack.jpg?direct&300|}} ((photo byHippysmack))|
-===== EZ-Just Thumbscrew Mods =====
+**IMS Mods**\\
 Several mods to the thumbscrew have been done to make counting turns while turning the screw easier. \\
@@ Line 72: / Line 82: @@
 |{{:techtalk:evo:carb:idle_mixture_screw_mod_by_folkie.jpg?direct&300|}}|
-===== Modding a Factory Mixture Screw =====
+**Factory IMS - Modding**
 This was done to extend the factory idle mixture screw. \\
@@ Line 82: / Line 92: @@
 \\
-===== Modding a Factory Idle Speed Screw =====
-You can stick a dime in the adjuster screw slot and braze it to the screw to make future adjustments by hand. \\
-{{:techtalk:ref:carb:keihin_carb_1_by_ddddylan_-_annotated.jpg?direct&300|}} ((photo by DDDDylan of the XLFORUM, annotated by Hippysmack))
 ====== Velocity Stack ======
@@ Line 94: / Line 101: @@
 It requires a total of 2 gaskets (included) to install. ((photos by Hippysmack)) \\
+This is a "V-Ductor" from CV Performance. ((https://cv-performance.com/v-ductor-installation)) \\
 |{{:techtalk:ref:carb:velocity_stack_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:carb:velocity_stack_2_by_hippysmack.jpg?direct&300|}}|
+  * Remove the air cleaner backing plate.
+  * Place a gasket onto the backing plate, then the V-Ductor and another gasket (2 supplied in the kit).
+  * The smaller end of the cone faces into the carb.
+  * Install the new assembly onto the carb and torque to factory specs.
+  * backing plate with as normal against the V-Ductor. Installation of your air box will vary depending upon the
 |{{:techtalk:ref:carb:velocity_stack_3_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:carb:velocity_stack_4_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:carb:velocity_stack_5_by_hippysmack.jpg?direct&300|}}|
@@ Line 252: / Line 266: @@
 Blow the passage out again to ensure of no debris before installing the bowl. ((photos by Hippysmack)) \\
 {{:techtalk:ref:carb:cv_fuel_inlet_elbow_mod_40_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:carb:cv_fuel_inlet_elbow_mod_41_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:carb:cv_fuel_inlet_elbow_mod_42_by_hippysmack.jpg?direct&300|}} \\
-====== Adjustable Main Jet (L76-87) ======
-There is an adjustable main jet available from J&P Cycles or others. \\
-These work great and you don't have to fool around jet guessing whether you have the right size main jet or not. \\
-They are simple to adjust. Just wind it up to about 65 MPH and run it in until it misses and back it out about a full turn. ((oldnavy of the XLFORUM http://xlforum.net/forums/showthread.php?t=877868&page=2)) \\
-This kit can be purchased online. It comes with an installation guide and index pointer. \\
-The tool marks inside of the float bowl (as installed) for drilling the proper sized hole to thread in the adjustable main jet.\\
-The kit can be purchased online. \\
-PDF instructions - [[http://www.vtwinmfg.com/instructions/35/35-0369.pdf]] \\
-{{:techtalk:ref:carb:keihin_butterfly_adjustable_main_jet_35-0369.jpg?direct&300|}} \\
-This replaces the main jet (has to be removed). \\
-The float bowl has to be removed to install the adjustable main jet. \\
-A guide tool is included with the kit to install the new jet to properly index the carburetor float bowl. \\
-A index pointer is installed in the guide, bowl reinstalled and the pointer is pushed down from inside the venture to dimple the bowl. \\
-The bowl is once again removed and a 1/16"-1/8" pilot hole is drilled followed by a 15/64" bit. \\
-After checking for burrs, removing the index tool and guide and cleaning up, the adjustable jet is installed in the float bowl. \\
-(partially unscrew the small 'T' handle so that the needle in the adjustable jet is not exposed to accidental damage) \\
-Remove the nut from the adjustable jet, insert the jet through the 15/64" hole drilled earlier. \\
-Then re-tighten the bowl and gently screw in the 'T' handle to the needle seat and then back it out 4 turns. \\
-Finer tuning can be achieved by reading the spark plugs and small adjustments to the “T” handle. \\
-This adjustable jet eliminates the chore of carrying and continually changing different main jets with every change in exhaust system or air cleaner. \\
-The hole in the bowl for the 'T' handle jet has to be indexed correctly in order for this to work. \\
-The adjustable main jet is designed to operate in conjunction with a 1.80 main jet included with the kit. \\
-Make sure you record or remember the number of turns off the seat and back off the 'T' handle before removing the float bowl later. \\
-This will help prevent needle / jet interference when the float bowl is reinstalled. \\
-For initial adjustment (standard pipes and A/C) it's recommended that the adjustment needle be backed out four (4) turns from the seat.
-The adjustable jet set screw is turned in, towards the float bowl to lean the fuel/air mixture and out from the float bowl to richen the mixture. \\
-Check plugs frequently after jet adjustment, exhaust or A/C to avoid too lean or too rich conditions. \\
-|{{:techtalk:ref:carb:kehien_butterfly_carb_1_by_leucadiaguit_-_cropped.jpg?direct&300|}}|{{:techtalk:ref:carb:kehien_butterfly_carb_2_by_leucadiaguit_-_cropped.jpg?direct&300|}}|

Trace:

Differences

Navigation

Search

Toolbox