Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:elec17 [2019/12/18 16:11] hippysmack [Misc Aftermarket Electrical Items 3] |
techtalk:ref:elec17 [2020/08/24 06:21] ixl2relax [Alternative to CANbus Key Switch] |
||
|---|---|---|---|
| Line 11: | Line 11: | ||
| **1998-2003 Models - BAS Bypass Mod** | **1998-2003 Models - BAS Bypass Mod** | ||
| - | The sensor is sometimes unreliable, either failing to allow the bike to start or by not shutting down on tipover. Some have chosen to bypass the unit, disconnecting the sensor and shorting the LtGreen/Gray Wire to the Black Wire in the wiring harness connector, while also capping the solid Gray wire (which is the power from the Ignition Fuse). This might activate a Check Engine Light error on the 1200S models (only). Some have used a voltage-divider, rather than a shorting jumper, to prevent the CEL error. From the BAS signal line (LtGn/Gy) on the harness connector, connect a 1K resistor to the 12v power line (Gray) and another 1K resistor to the ground line (Black) - This keeps the BAS signal line near 6.4v. ((http://xlforum.net/forums/showthread.php?t=1768777)) | + | The sensor is sometimes unreliable, either failing to allow the bike to start or by not shutting down on tipover. Some have chosen to bypass the unit, disconnecting the sensor and shorting the LtGreen/Gray Wire to the Black Wire in the wiring harness connector, while also capping the solid Gray wire (which is the power from the Ignition Fuse). This might activate a Check Engine Light error on the 1200S models (only). Some have used a voltage-divider, rather than a shorting jumper, to prevent the CEL error. From the BAS signal line (LtGn/Gy) on the harness connector, connect a 1K resistor to the 12v power line (Gray) and another 1K resistor to the ground line (Black) - This keeps the BAS signal line near 6.4v. ((http://xlforum.net/forums/showthread.php?t=1768777))\\ |
| + | {{:techtalk:ref:elec:bas-bypass-98-03.jpg?300|}} | ||
| **2004-2013 Models - BAS Bypass Mod** | **2004-2013 Models - BAS Bypass Mod** | ||
| Line 32: | Line 33: | ||
| (Just an aside - You could buy just (4) 220-ohm resistors. Solder (3) in series to create 660-ohms (instead of the 680-ohm resistor) and use the final 220-ohm resistor as shown.) | (Just an aside - You could buy just (4) 220-ohm resistors. Solder (3) in series to create 660-ohms (instead of the 680-ohm resistor) and use the final 220-ohm resistor as shown.) | ||
| + | |||
| + | \\ | ||
| + | |||
| + | |||
| + | ===== Alternative (CANbus) Handlebar Switches ===== | ||
| + | |||
| + | This thread is about removing the circuit boards that are CANbus controllers from the Handlebar Control Housings and placing them (while being connected) below the seat. This allows alternative switch housings to be used on the handlebars with appropriate wire connections to the moved circuit boards. | ||
| + | |||
| + | I should get you started (although it is not a full tutorial). It should also be helpful for eliminating the on-handlebar controls (that is, removing them, visually, without replacing them). | ||
| + | |||
| + | [[http://xlforum.net/forums/showthread.php?t=1914482| | ||
| + | Different Handlebar Switches With CAN Bus]] | ||
| + | |||
