Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
techtalk:ref:engmech01e [2018/07/07 16:09]
hippysmack [Installing a Helicoil on a Drain Plug with the Engine in the Frame]
techtalk:ref:engmech01e [2018/07/07 18:50]
hippysmack [Installing a Helicoil on a Drain Plug with the Engine in the Frame]
Line 10: Line 10:
 {{:​techtalk:​ref:​engmech:​primary_drain_plug_repair_1_by_freewheeler.jpg?​direct&​400|}} ((photo by Freewheeler of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1852458&​highlight=stripped+plug)) ​ {{:​techtalk:​ref:​engmech:​drain_plug_repair_1_by_xlchjoe.jpg?​direct&​400|}} ((photo by xlchjoe of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1200190&​page=58)) ​ {{:​techtalk:​ref:​engmech:​primary_drain_plug_repair_1_by_freewheeler.jpg?​direct&​400|}} ((photo by Freewheeler of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1852458&​highlight=stripped+plug)) ​ {{:​techtalk:​ref:​engmech:​drain_plug_repair_1_by_xlchjoe.jpg?​direct&​400|}} ((photo by xlchjoe of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1200190&​page=58)) ​
  
-  * Using a drill with a handle will help keep the hole square. The hole needs to be good and straight for the new plug to seal. +  * Using a drill with a handle will help keep the hole square. The hole needs to be good and straight for the new plug to seal. 
 +  * You can also buy a bushing with a good flush end and drill thru it while keeping it tight against the case to help keep the hole straight.  
 + 
 +|  Helicoiled threads have to be tapped straight with the sealing surface to allow a 360º \\ seal underneath the plug head or the plug will leak. ((photo by xlchjoe of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1200190&​page=58)) ((photo by sevenyears of famine of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1461031&​highlight=stripped+primary+drain&​page=6)) ​ || 
 +|{{:​techtalk:​ref:​engmech:​drain_plug_repair_2_by_xlchjoe.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​helicoiled_plug_hole_1_by_sevenyears_of_famine.jpg?​direct&​300|}}| 
   * Before drilling, the hole was packed with grease and a small piece of stainless was put on the other side to keep from drilling \\ anything and (hopefully) stopping some of the chips from falling further into the engine. ((photos by Freewheeler of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1852458&​highlight=stripped+plug))   * Before drilling, the hole was packed with grease and a small piece of stainless was put on the other side to keep from drilling \\ anything and (hopefully) stopping some of the chips from falling further into the engine. ((photos by Freewheeler of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1852458&​highlight=stripped+plug))