Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
techtalk:ref:engmech01h [2020/08/24 01:58] hippysmack [Test Fitting] |
techtalk:ref:engmech01h [2024/01/14 18:19] (current) hippysmack |
||
|---|---|---|---|
| Line 8: | Line 8: | ||
| Upgrades such as bigger cams and valves sometimes comes with more clearancing needed. \\ | Upgrades such as bigger cams and valves sometimes comes with more clearancing needed. \\ | ||
| Below are some examples of clearance issues to check before / during assembly. \\ | Below are some examples of clearance issues to check before / during assembly. \\ | ||
| + | |||
| ==== Cam Lobes ==== | ==== Cam Lobes ==== | ||
| - | + | |The underside of the lifter bosses often need a little \\ grinding to keep the cam lobes from contacting. ((photo by aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/30069-se-575-install-vs-se-536-install#post662315))|Big cam lobes also may try to hit the pinion race, \\ which protrudes from the case slightly. It sticks out \\ farther on 2000-up motors. ((photo by aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/30069-se-575-install-vs-se-536-install#post662315))|If the lobe is contacting the pinion race, it's better to \\ modify the lobe than the race (this is a Red Shift 567). \\ Notice the chamfer on the lobe below. Modifying that \\ race is difficult and risky. People have done it and \\ trashed the bearing in the process. ((photo by aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/30069-se-575-install-vs-se-536-install#post662315))| | |
| - | |The underside of the lifter bosses often need a little \\ grinding to keep the cam lobes from contacting. ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?p=668404#post668404))|Big cam lobes also may try to hit the pinion race, \\ which protrudes from the case slightly. It sticks out \\ farther on 2000-up motors. ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?p=668404#post668404))|If the lobe is contacting the pinion race, it's better to \\ modify the lobe than the race (this is a Red Shift 567). \\ Notice the chamfer on the lobe below. Modifying that \\ race is difficult and risky. People have done it and \\ trashed the bearing in the process. ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?p=668404#post668404))| | + | |
| |{{:techtalk:ref:engmech:clearancing_the_engine_for_bigger_cams_1_by_aswracing.jpg?direct&300|}}|{{:techtalk:ref:engmech:clearancing_the_engine_for_bigger_cams_2_by_aswracing.jpg?direct&300|}}|{{:techtalk:ref:engmech:clearancing_the_engine_for_bigger_cams_3_by_aswracing.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:clearancing_the_engine_for_bigger_cams_1_by_aswracing.jpg?direct&300|}}|{{:techtalk:ref:engmech:clearancing_the_engine_for_bigger_cams_2_by_aswracing.jpg?direct&300|}}|{{:techtalk:ref:engmech:clearancing_the_engine_for_bigger_cams_3_by_aswracing.jpg?direct&300|}}| | ||
| - | An example of chamfering the cam lobes was done by XLF member ~Grind~: ((http://xlforum.net/forums/showthread.php?t=1448694)) \\ | + | An example of chamfering the cam lobes was done by XLF member ~Grind~: ((https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) \\ |
| - | {{:techtalk:ref:engmech:clearancing_cam_lobes_1_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:ref:engmech:clearancing_cam_lobes_2_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:ref:engmech:clearancing_cam_lobes_3_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) \\ | + | {{:techtalk:ref:engmech:clearancing_cam_lobes_1_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) {{:techtalk:ref:engmech:clearancing_cam_lobes_2_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) {{:techtalk:ref:engmech:clearancing_cam_lobes_3_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) \\ |
| - | + | ||
| - | {{:techtalk:ref:engmech:clearancing_cam_lobes_4_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:ref:engmech:clearancing_cam_lobes_5_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:ref:engmech:clearancing_cam_lobes_6_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) \\ | + | |
| + | {{:techtalk:ref:engmech:clearancing_cam_lobes_4_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) {{:techtalk:ref:engmech:clearancing_cam_lobes_5_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) {{:techtalk:ref:engmech:clearancing_cam_lobes_6_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) \\ | ||
| ==== Lifters ==== | ==== Lifters ==== | ||
| See also [[techtalk:evo:engmech02b|91-99 Lifter Pin Upgrade to 00-05 Lifter Pin Screws]] in the Sportsterpedia. \\ | See also [[techtalk:evo:engmech02b|91-99 Lifter Pin Upgrade to 00-05 Lifter Pin Screws]] in the Sportsterpedia. \\ | ||
| - | Another thing to check is tappet pin clearance. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?p=668404#post668404)) \\ | + | Another thing to check is tappet pin clearance. ((aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/30069-se-575-install-vs-se-536-install#post662315)) \\ |
| The tappet pin rests against the flat on the tappet to keep the tappet from rotating in the bore. \\ | The tappet pin rests against the flat on the tappet to keep the tappet from rotating in the bore. \\ | ||
| But a bigger cam lobe lifts the tappet farther and on stock lifter, it can run out of travel. \\ | But a bigger cam lobe lifts the tappet farther and on stock lifter, it can run out of travel. \\ | ||
| Aftermarket lifters as shown below sometimes have longer flats. \\ | Aftermarket lifters as shown below sometimes have longer flats. \\ | ||
| - | |Stock vs Jims lifter tappet flat comparison. ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?p=668404#post668404))| | + | |Stock vs Jims lifter tappet flat comparison. ((photo by aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/30069-se-575-install-vs-se-536-install#post662315))| |
| |{{:techtalk:ref:engmech:tappet_pin_comparison_2_by_aswracing.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:tappet_pin_comparison_2_by_aswracing.jpg?direct&300|}}| | ||
| Line 43: | Line 42: | ||
| Four plugs were made to go in the camshaft bushings to keep from hitting them with the die grinder. \\ | Four plugs were made to go in the camshaft bushings to keep from hitting them with the die grinder. \\ | ||
| - | {{:techtalk:ref:engmech:clearancing_lifter_bore_od_1_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:ref:engmech:clearancing_lifter_bore_od_2_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) {{:techtalk:ref:engmech:clearancing_lifter_bore_od_3_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM http://xlforum.net/forums/showthread.php?t=1448694)) \\ | + | {{:techtalk:ref:engmech:clearancing_lifter_bore_od_1_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) {{:techtalk:ref:engmech:clearancing_lifter_bore_od_2_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) {{:techtalk:ref:engmech:clearancing_lifter_bore_od_3_by_grind.jpg?direct&170|}} ((photo by ~Grind~ of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/134422-~grinds~-hammer-performance-1250-build?t=1448694)) \\ |
| ==== Rocker Box ==== | ==== Rocker Box ==== | ||
| See more on [[techtalk:evo:engmech04b#rocker_box_rocker_arm_inspection_and_servicing|Clearancing and inspecting the Rocker Boxes]] in the Sportsterpedia. \\ | See more on [[techtalk:evo:engmech04b#rocker_box_rocker_arm_inspection_and_servicing|Clearancing and inspecting the Rocker Boxes]] in the Sportsterpedia. \\ | ||
| Line 53: | Line 53: | ||
| Then remove the cover and see if anything got up intp the clay and where. \\ | Then remove the cover and see if anything got up intp the clay and where. \\ | ||
| - | Pull the tops and look for little marks on the inside. ((HAMMERSALES of the XLFORUM http://xlforum.net/forums/showthread.php?t=1120605)) \\ | + | Pull the tops and look for little marks on the inside. ((HAMMERSALES of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/116559-back-with-another-cam-question?t=1120605)) \\ |
| There shouldn't be any outside of factory casting marks. \\ | There shouldn't be any outside of factory casting marks. \\ | ||
| Rocker or pushrod contact will appear as marks that shouldn't be there. \\ | Rocker or pushrod contact will appear as marks that shouldn't be there. \\ | ||
| Line 60: | Line 60: | ||
| Occasionally, 536 cams can cause the rocker arms to hit the rocker box tops (on the pushrod side). \\ | Occasionally, 536 cams can cause the rocker arms to hit the rocker box tops (on the pushrod side). \\ | ||
| This is rare, but it can happen. \\ | This is rare, but it can happen. \\ | ||
| - | Contact here should cause any damage, but it'll cause noise and leaks. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?p=5489961)) \\ | + | Contact here should cause any damage, but it'll cause noise and leaks. ((aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-buell-motorcycle-racing/sportster-motorcycle-drag-racing/186625-lets-see-your-off-season-builds/page16#post4033634)) \\ |
| A lot of rocker box top leaks have been traced to this. | A lot of rocker box top leaks have been traced to this. | ||
| Line 66: | Line 66: | ||
| If the valve spring or retainer is allowed to touch the rocker box, it forces the valve to land sideways on the seat. \\ | If the valve spring or retainer is allowed to touch the rocker box, it forces the valve to land sideways on the seat. \\ | ||
| - | | Rocker box top damage ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?p=5489961)) | Lower rocker damage from valve spring impact ((photo by ReddTigger of the XLFORUM http://xlforum.net/forums/showthread.php?p=4593655)) | | + | | Rocker box top damage ((photo by aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-buell-motorcycle-racing/sportster-motorcycle-drag-racing/186625-lets-see-your-off-season-builds/page16#post4033634)) | Lower rocker damage from valve spring impact ((photo by ReddTigger of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-motor-top-end/157656-rocker-box-clearance-damage#post3347479)) | |
| |{{:techtalk:evo:engmech:rocker_box_clearance_3_by_aswracing.jpg?direct&300|}}|{{:techtalk:evo:engmech:rocker_box_damage_3_by_reddtigger.jpg?direct&300|}}| | |{{:techtalk:evo:engmech:rocker_box_clearance_3_by_aswracing.jpg?direct&300|}}|{{:techtalk:evo:engmech:rocker_box_damage_3_by_reddtigger.jpg?direct&300|}}| | ||
| Line 78: | Line 78: | ||
| Clearance can be done with a die grinder or Dremil Tool. | Clearance can be done with a die grinder or Dremil Tool. | ||
| - | |You can see where the contact occurs. ((photos by madnss of the XLFORUM http://xlforum.net/forums/showthread.php?t=1776474&highlight=rocker+arm+bushings))|| | + | |You can see where the contact occurs. ((photos by madnss of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-motor-top-end/165126-big-cams-s-s-roller-rockers?t=1776474&highlight=rocker+arm+bushings))|| |
| |{{:techtalk:evo:engmech:rocker_box_clearance_1_by_madnss.jpg?direct&200|}}|{{:techtalk:evo:engmech:rocker_box_clearance_2_by_madnss.jpg?direct&200|}}| | |{{:techtalk:evo:engmech:rocker_box_clearance_1_by_madnss.jpg?direct&200|}}|{{:techtalk:evo:engmech:rocker_box_clearance_2_by_madnss.jpg?direct&200|}}| | ||
| \\ | \\ | ||
| Line 85: | Line 85: | ||
| From Hammer Performance: [[http://www.hammerperf.com/ttxlcaminstall.shtml]] \\ | From Hammer Performance: [[http://www.hammerperf.com/ttxlcaminstall.shtml]] \\ | ||
| From NRHS: [[http://www.nrhsperformance.com/tech_xlcaminstall.shtml]] \\ | From NRHS: [[http://www.nrhsperformance.com/tech_xlcaminstall.shtml]] \\ | ||
| + | |||
| ====== Test Fitting ====== | ====== Test Fitting ====== | ||
| - | Factory fitting of the cams is (or rather was) all about noise control. ((aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1840595)) \\ | + | Factory fitting of the cams is (or rather was) all about noise control. ((aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/171721-4-speed-cams-and-gear-case-mix-and-match?t=1840595)) \\ |
| By selecting the cam gears sized specifically for the engine they were going in, they could walk that fine line between noisy and too-tight. \\ | By selecting the cam gears sized specifically for the engine they were going in, they could walk that fine line between noisy and too-tight. \\ | ||
| The noise from the gears being a tad loose doesn't hurt anything. Too-tight however can cause localized tooth heating and failure. \\ | The noise from the gears being a tad loose doesn't hurt anything. Too-tight however can cause localized tooth heating and failure. \\ | ||
| Line 104: | Line 105: | ||
| Then, install all 4 cams in the cam cover and make sure they spin freely without binding. \\ | Then, install all 4 cams in the cam cover and make sure they spin freely without binding. \\ | ||
| On 2003 and earlier motors, the cams can be rotated thru the nosecone ignition cover. 2004-up covers don't have this hole. \\ | On 2003 and earlier motors, the cams can be rotated thru the nosecone ignition cover. 2004-up covers don't have this hole. \\ | ||
| - | However, several folks have ran 2000-2003 covers on 3004-up motors with no issues. ((NRHS Sales of the XLFORUM http://xlforum.net/forums/showthread.php?t=1756724&page=23)) \\ | + | However, several folks have ran 2000-2003 covers on 3004-up motors with no issues. ((NRHS Sales of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/163447-spun-2-outer-bushing-again/page23?t=1756724&page=23)) \\ |
| - | | Test fitting cams in the cam cover ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1715966&page=3)) |Test fitting cams with the cam cover installed ((photo by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1840595))| | + | | Test fitting cams in the cam cover ((photo by aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/159973-conversion-redo/page3?t=1715966&page=3)) |Test fitting cams with the cam cover installed ((photo by aswracing of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/171721-4-speed-cams-and-gear-case-mix-and-match?t=1840595))| |
| |{{:techtalk:ref:engmech:test_fit_cams_in_cam_cover_by_aswracing.jpg?direct&300|}}|{{:techtalk:ref:engmech:test_fitting_cams_with_the_cam_cover_on_by_aswracing.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:test_fit_cams_in_cam_cover_by_aswracing.jpg?direct&300|}}|{{:techtalk:ref:engmech:test_fitting_cams_with_the_cam_cover_on_by_aswracing.jpg?direct&300|}}| | ||
