Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:ref:engmech01t [2019/05/25 14:05] hippysmack [DIY Front Left Motor Mount] |
techtalk:ref:engmech01t [2024/01/14 20:37] (current) hippysmack |
||
---|---|---|---|
Line 2: | Line 2: | ||
====== REF: Engine Mechanicals - Sub-01T ====== | ====== REF: Engine Mechanicals - Sub-01T ====== | ||
====== DIY Front Left Motor Mount ====== | ====== DIY Front Left Motor Mount ====== | ||
- | This top engine mount is made out of 4mm steel starting with a cardboard template sized, shaped and drilled. ((photos by Jorgen of the XLFORUM http://xlforum.net/forums/showthread.php?t=1619616&page=21)) \\ | + | This top engine mount is made out of 4mm steel starting with a cardboard template sized, shaped and drilled. ((photos by Jörgen of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/149281-124-1993-xlh-build-thread/page21?t=1619616&page=21)) \\ |
|{{:techtalk:ref:engmech:diy_front_left_motor_mount_1_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_2_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_3_by_jorgen.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:diy_front_left_motor_mount_1_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_2_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_3_by_jorgen.jpg?direct&300|}}| | ||
Line 10: | Line 10: | ||
Having this bend at the correct angle and position is crucial. \\ | Having this bend at the correct angle and position is crucial. \\ | ||
Otherwise the piece would have to be discarded to start all over again. \\ | Otherwise the piece would have to be discarded to start all over again. \\ | ||
- | It has to match up to the frame without distorting upon torque. ((photos by Jorgen of the XLFORUM http://xlforum.net/forums/showthread.php?t=1619616&page=21)) \\ | + | It has to match up to the frame without distorting upon torque. ((photos by Jörgen of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/149281-124-1993-xlh-build-thread/page21?t=1619616&page=21)) \\ |
|{{:techtalk:ref:engmech:diy_front_left_motor_mount_4_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_5_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_6_by_jorgen.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:diy_front_left_motor_mount_4_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_5_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_6_by_jorgen.jpg?direct&300|}}| | ||
The mount was placed over a small vise (with the jaws opened and the edges rounded to help the bending process of the mount material). \\ | The mount was placed over a small vise (with the jaws opened and the edges rounded to help the bending process of the mount material). \\ | ||
- | After bending, the mount is test fitted for a flush fit to the frame. ((photos by Jorgen of the XLFORUM http://xlforum.net/forums/showthread.php?t=1619616&page=21)) \\ | + | After bending, the mount is test fitted for a flush fit to the frame. ((photos by Jörgen of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/149281-124-1993-xlh-build-thread/page21?t=1619616&page=21)) \\ |
|{{:techtalk:ref:engmech:diy_front_left_motor_mount_7_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_8_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_9_by_jorgen.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:diy_front_left_motor_mount_7_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_8_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_9_by_jorgen.jpg?direct&300|}}| | ||
- | Then two gussets were fabricated using the above method of bending and then welded to the mount on both sides. ((photos by Jorgen of the XLFORUM http://xlforum.net/forums/showthread.php?t=1619616&page=21)) \\ | + | Then two gussets were fabricated using the above method of bending and then welded to the mount on both sides. ((photos by Jörgen of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/149281-124-1993-xlh-build-thread/page21?t=1619616&page=21)) \\ |
|{{:techtalk:ref:engmech:diy_front_left_motor_mount_10_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_11_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_12_by_jorgen.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:diy_front_left_motor_mount_10_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_11_by_jorgen.jpg?direct&300|}}|{{:techtalk:ref:engmech:diy_front_left_motor_mount_12_by_jorgen.jpg?direct&300|}}| |