Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
techtalk:ref:engmech01t [2019/05/25 14:05]
hippysmack [DIY Front Left Motor Mount]
techtalk:ref:engmech01t [2019/05/25 14:39] (current)
hippysmack
Line 2: Line 2:
 ====== REF: Engine Mechanicals - Sub-01T ====== ====== REF: Engine Mechanicals - Sub-01T ======
 ====== DIY Front Left Motor Mount ====== ====== DIY Front Left Motor Mount ======
-This top engine mount is made out of 4mm steel starting with a cardboard template sized, shaped and drilled. ((photos by Jorgen ​of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1619616&​page=21)) \\+This top engine mount is made out of 4mm steel starting with a cardboard template sized, shaped and drilled. ((photos by Jörgen ​of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1619616&​page=21)) \\
  
 |{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_1_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_2_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_3_by_jorgen.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_1_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_2_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_3_by_jorgen.jpg?​direct&​300|}}|
Line 10: Line 10:
 Having this bend at the correct angle and position is crucial. \\ Having this bend at the correct angle and position is crucial. \\
 Otherwise the piece would have to be discarded to start all over again. \\ Otherwise the piece would have to be discarded to start all over again. \\
-It has to match up to the frame without distorting upon torque. ((photos by Jorgen ​of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1619616&​page=21)) \\+It has to match up to the frame without distorting upon torque. ((photos by Jörgen ​of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1619616&​page=21)) \\
  
 |{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_4_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_5_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_6_by_jorgen.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_4_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_5_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_6_by_jorgen.jpg?​direct&​300|}}|
  
 The mount was placed over a small vise (with the jaws opened and the edges rounded to help the bending process of the mount material). \\ The mount was placed over a small vise (with the jaws opened and the edges rounded to help the bending process of the mount material). \\
-After bending, the mount is test fitted for a flush fit to the frame. ((photos by Jorgen ​of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1619616&​page=21)) \\+After bending, the mount is test fitted for a flush fit to the frame. ((photos by Jörgen ​of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1619616&​page=21)) \\
  
 |{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_7_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_8_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_9_by_jorgen.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_7_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_8_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_9_by_jorgen.jpg?​direct&​300|}}|
  
-Then two gussets were fabricated using the above method of bending and then welded to the mount on both sides. ((photos by Jorgen ​of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1619616&​page=21)) \\+Then two gussets were fabricated using the above method of bending and then welded to the mount on both sides. ((photos by Jörgen ​of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1619616&​page=21)) \\
  
 |{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_10_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_11_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_12_by_jorgen.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_10_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_11_by_jorgen.jpg?​direct&​300|}}|{{:​techtalk:​ref:​engmech:​diy_front_left_motor_mount_12_by_jorgen.jpg?​direct&​300|}}|