Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:engmech02f [2019/06/12 04:01] hippysmack [Installing Hammer Performance Billet Pushrod Base Kit] |
techtalk:ref:engmech02f [2019/08/04 01:53] hippysmack [Installing Hammer Performance Billet Pushrod Base Kit] |
||
---|---|---|---|
Line 67: | Line 67: | ||
|{{:techtalk:ref:engmech:hammerperf_pushrod_bases_19_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:hammerperf_pushrod_bases_20_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:hammerperf_pushrod_bases_21_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:hammerperf_pushrod_bases_19_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:hammerperf_pushrod_bases_20_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:hammerperf_pushrod_bases_21_by_hippysmack.jpg?direct&300|}}| | ||
- | * Check the clearance between the tubes and cylinder fins before installing the bolts. \\ On big cylinders, you may have to grind some off the fins to get a good fit between them. | + | **Check the clearance between the tubes and cylinder fins before installing the bolts**. \\ |
+ | On big cylinders, you may have to grind some off the fins to get a good fit between them. | ||
| (R) (fins 90" jugs had to be ground for tube clearance) (F) ((photos by DonChicago48 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1610587&page=21)) || | | (R) (fins 90" jugs had to be ground for tube clearance) (F) ((photos by DonChicago48 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1610587&page=21)) || | ||
|{{:techtalk:ref:engmech:hammerperf_rear_pushrod_tube_clearance_issue_by_donchicago48.jpg?direct&300|}}|{{:techtalk:ref:engmech:hammerperf_front_pushrod_tube_clearance_issue_by_donchicago48.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:hammerperf_rear_pushrod_tube_clearance_issue_by_donchicago48.jpg?direct&300|}}|{{:techtalk:ref:engmech:hammerperf_front_pushrod_tube_clearance_issue_by_donchicago48.jpg?direct&300|}}| | ||
+ | |||
+ | Also check that the cylinder base gasket isn't interfering with the pushrod tube base. ((DonChicago48 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1610587&page=17)) \\ | ||
+ | It could hang up on the gasket and potentially cause an oil leak. \\ | ||
+ | You may have to trim the cylinder base gasket to clear the pushrod base retainer. \\ | ||
+ | You can use the edge of the bottom gasket mating surface as a cutting guide. \\ | ||
+ | With a sharp ExActo Knife, cut the gasket along the outline of the cylinder base edge. \\ | ||
+ | |||
+ | | Trimming the base gasket. ((DonChicago48 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1610587&page=17)) || | ||
+ | |{{:techtalk:ref:engmech:trimming_axtell_base_gasket_1_by_donchicago48.jpg?direct&300|}}|{{:techtalk:ref:engmech:trimming_axtell_base_gasket_2_by_donchicago48.jpg?direct&300|}}| | ||
* Push the base down onto the case deck and hold pressure on the base with one hand. | * Push the base down onto the case deck and hold pressure on the base with one hand. |