Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | |||
|
techtalk:ref:engmech02f [2019/08/04 01:53] hippysmack [Installing Hammer Performance Billet Pushrod Base Kit] |
techtalk:ref:engmech02f [2024/01/14 21:04] hippysmack |
||
|---|---|---|---|
| Line 70: | Line 70: | ||
| On big cylinders, you may have to grind some off the fins to get a good fit between them. | On big cylinders, you may have to grind some off the fins to get a good fit between them. | ||
| - | | (R) (fins 90" jugs had to be ground for tube clearance) (F) ((photos by DonChicago48 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1610587&page=21)) || | + | | (R) (fins 90" jugs had to be ground for tube clearance) (F) ((photos by DonChicago48 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/frame-mount-evo-sportster-talk-1986-2003-models/148266-building-a-90-inch-sledge-hammer/page21?t=1610587&page=21)) || |
| |{{:techtalk:ref:engmech:hammerperf_rear_pushrod_tube_clearance_issue_by_donchicago48.jpg?direct&300|}}|{{:techtalk:ref:engmech:hammerperf_front_pushrod_tube_clearance_issue_by_donchicago48.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:hammerperf_rear_pushrod_tube_clearance_issue_by_donchicago48.jpg?direct&300|}}|{{:techtalk:ref:engmech:hammerperf_front_pushrod_tube_clearance_issue_by_donchicago48.jpg?direct&300|}}| | ||
| - | Also check that the cylinder base gasket isn't interfering with the pushrod tube base. ((DonChicago48 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1610587&page=17)) \\ | + | Also check that the cylinder base gasket isn't interfering with the pushrod tube base. ((DonChicago48 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/frame-mount-evo-sportster-talk-1986-2003-models/148266-building-a-90-inch-sledge-hammer/page17?t=1610587&page=17)) \\ |
| It could hang up on the gasket and potentially cause an oil leak. \\ | It could hang up on the gasket and potentially cause an oil leak. \\ | ||
| You may have to trim the cylinder base gasket to clear the pushrod base retainer. \\ | You may have to trim the cylinder base gasket to clear the pushrod base retainer. \\ | ||
| Line 79: | Line 79: | ||
| With a sharp ExActo Knife, cut the gasket along the outline of the cylinder base edge. \\ | With a sharp ExActo Knife, cut the gasket along the outline of the cylinder base edge. \\ | ||
| - | | Trimming the base gasket. ((DonChicago48 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1610587&page=17)) || | + | | Trimming the base gasket. ((DonChicago48 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/frame-mount-evo-sportster-talk-1986-2003-models/148266-building-a-90-inch-sledge-hammer/page17?t=1610587&page=17)) || |
| |{{:techtalk:ref:engmech:trimming_axtell_base_gasket_1_by_donchicago48.jpg?direct&300|}}|{{:techtalk:ref:engmech:trimming_axtell_base_gasket_2_by_donchicago48.jpg?direct&300|}}| | |{{:techtalk:ref:engmech:trimming_axtell_base_gasket_1_by_donchicago48.jpg?direct&300|}}|{{:techtalk:ref:engmech:trimming_axtell_base_gasket_2_by_donchicago48.jpg?direct&300|}}| | ||
