Differences

This shows you the differences between two versions of the page.

--- techtalk:ref:oil13 [2021/02/22 04:08]
hippysmack [Remote Oil Filters]
+++ techtalk:ref:oil13 [2021/02/22 04:43]
hippysmack
@@ Line 2: / Line 2: @@
 ====== REF: Oiling & Lubrication ======
 ====== Remote Oil Filters ======
-It is also commonly known that the more oil you hold, the more motor heat can be transferred to dissipate that heat. \\
+The stock oil filter (HD 63782-80T) is the small one that is usually used on custom bikes. Chrome or black can be found. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=563241)) \\
+However, it is also commonly known that the more oil you hold, the more motor heat can be transferred to dissipate that heat. \\
 Race bikes have huge oil tanks for that reason. ((Monte03 of the XLFORUM http://xlforum.net/forums/showthread.php?t=563241)) \\
 If you go the filter route, be sure to purge the lines by bleeding the pump front nipple first while running. \\
 Then take the return line and place it into a pail before you connect to the barb tank fitting so you assure a complete circle has been made.
+====== Plumbing to Oil Filter ======
+**Note**: On all spin on oil filters, dirty oil goes in the outside of the filter. Clean oil comes out the center. (( ryder rick of the XLFORUM http://xlforum.net/forums/showthread.php?p=5643382&highlight=oil+filter+bracket#post5643382)) \\
+If you are not sure, start the motor momentarily with the filter off and if oil is pumped out the center port, you have it backwards. \\
 |  74 XLH Oil Filter Plumbing ((photo by vyper202 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1570042))  |
 |{{:techtalk:ih:oil:74_oil_line_routing_4_by_vyper202.jpg?direct&300|}}|
+====== Parts / Kits ======
 Below is a parts list for a remote oil filter setup although it's not a kit per say; ((HolyHandGrenade of the XLFORUM http://xlforum.net/forums/showthread.php?t=1189337)) \\
@@ Line 18: / Line 28: @@
 {{:techtalk:ref:oil:remote_oil_filter_parts_by_holyhandgrenade.jpg?direct&300|}} ((photo by HolyHandGrenade of the XLFORUM http://xlforum.net/forums/showthread.php?t=1189337))
 ----
@@ Line 48: / Line 59: @@
 {{:techtalk:ref:oil:oil_filter_relocation_kit_by_dk_custom.jpg?direct&300|}} ((photo by DK Custom of the XLFORUM http://xlforum.net/forums/showthread.php?p=5511484))
-====== Ironhead Oil Filter Locations ======
+====== Forward Mounting ======
-====== Forward mounted filters ======
 ===== On the left motor mount =====
@@ Line 65: / Line 75: @@
 |{{:techtalk:ref:oil:motor_mount_filter_adapter_on_69_xlch_1_by_nutter.jpg?direct&300|}}|{{:techtalk:ref:oil:motor_mount_filter_adapter_by_konel1.jpg?direct&300|}}|{{:techtalk:ih:oil:80_xlh_left_side_by_hscic.jpg?direct&300|}}|
+====== Modified and Custom Oil Filter Mounts ======
+\\
 ===== Modifying a standard motor mount for use as a oil filter mount =====
@@ Line 84: / Line 95: @@
 |  Standard motor mount mod for addition of an oil filter ((photos by bustert of the XLFORUM http://xlforum.net/forums/showthread.php?t=1266793))  ||  Marking the center hole for the filter ((drawing by Hippysmack))  |
 |{{:techtalk:ref:oil:ih_oil_filter_mount_1_by_bustert.jpg?direct&300|}}|{{:techtalk:ref:oil:ih_oil_filter_mount_2_by_bustert.jpg?direct&300|}}|{{:techtalk:ref:oil:finding_center_of_a_circle_by_hippysmack.jpg?direct&300|}}|
   * **Plug the small hole in the left motor mount**: \\ (hole #1 in the pic above)
@@ Line 144: / Line 154: @@
 ===== Build Your Own Motor / Oil Filter Mount =====
 Article by sifty of the XLFORUM ((http://xlforum.net/forums/showthread.php?page=22&t=1592463)) \\
@@ Line 198: / Line 209: @@
 |{{:techtalk:ref:oil:homemade_oil_filter_mount_16_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:oil:homemade_oil_filter_mount_17_by_sifty.jpg?direct&300|}}|{{:techtalk:ref:oil:homemade_oil_filter_mount_18_by_sifty.jpg?direct&300|}}|
 ===== Other forward positions =====
@@ Line 207: / Line 219: @@
 |A simple bracket with a piece of angle iron bolted to the right frame rail. \\ An automotive spin on filter mount with a 3/4"-16 threaded stem was bolted to it. \\ The PH6022 filter is Fram's cross reference with Harley 63805-80. ((DDDDylan of the XLFORUM http://xlforum.net/forums/showthread.php?p=5280955&highlight=oil+filter+bracket#post5280955))||
 |{{:techtalk:ref:oil:remote_oil_filter_2_by_ddddylan.jpg?direct&300|}}|{{:techtalk:ref:oil:remote_oil_filter_1_by_ddddylan.jpg?direct&300|}}|
 ----
@@ Line 214: / Line 225: @@
 The filter adapter is 5/"x24. However, you can buy adapters online to increase the adapter size to 13/16" or 3/4". \\
 |{{:techtalk:ref:oil:oil_filter_and_cooler_by_blight.jpg?direct&250|}}|
 ----
 This reportedly an old drag specialties item from the early eighty's. ((hasselme0 of the XLFORUM http://xlforum.net/forums/showthread.php?t=1078240&page=3)) ((photos by 78ironhead of the XLFORUM http://xlforum.net/forums/showthread.php?t=1078240&page=3)) \\
@@ Line 224: / Line 233: @@
 |{{:techtalk:ref:oil:oil_filter_-_cooler_1_by_78ironhead.jpg?direct&300|}}|{{:techtalk:ref:oil:oil_filter_-_cooler_3_by_78ironhead.jpg?direct&300|}}|
 ====== Rear mounted filters ======

Trace:

Differences

Navigation

Search

Toolbox