Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:priclutch01 [2018/06/17 04:45] hippysmack [Removing the Magnets] |
techtalk:ref:priclutch01 [2018/06/17 05:00] hippysmack [Removing the Magnets] |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| |{{:techtalk:ref:priclutch:broken_stator_magnets_1_by_vanmor.jpg?direct&300|}}|{{:techtalk:ref:priclutch:broken_stator_magnets_2_by_vanmor.jpg?direct&300|}}| | |{{:techtalk:ref:priclutch:broken_stator_magnets_1_by_vanmor.jpg?direct&300|}}|{{:techtalk:ref:priclutch:broken_stator_magnets_2_by_vanmor.jpg?direct&300|}}| | ||
| - | This was done on purpose as an illustration. "I started slow and then went a little harder until I heard a couple of the magnets drop out". ((Vanmor of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666986&highlight=stator+repair)) | + | This was done on purpose as an illustration. "I started slow and then went a little harder until I heard a couple of the magnets drop out". \\ As you can see, two of the magnets broke and then fell out. The surface of the magnet that was glued stayed in contact with the rotor. \\ Actually the two broken magnets shattered. They're ceramic and will break like glass.((Vanmor of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666986&highlight=stator+repair)) |
| ===== Sourcing Replacement Magnets ===== | ===== Sourcing Replacement Magnets ===== | ||
| Line 41: | Line 41: | ||
| * You can put it in an oven at 400*, you want to heat it evenly as spot heating can cause distortion. The magnets are brittle so be careful. ((bustert of the XLFORUM http://xlforum.net/forums/showthread.php?t=2000061&highlight=splines+hub&page=2)) | * You can put it in an oven at 400*, you want to heat it evenly as spot heating can cause distortion. The magnets are brittle so be careful. ((bustert of the XLFORUM http://xlforum.net/forums/showthread.php?t=2000061&highlight=splines+hub&page=2)) | ||
| - | * This one was set inside a charcoal grill with charcoal laid in a circle around it. ((Vanmor of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666986&highlight=stator+repair)) \\ (Note: Best to place the charcoal all the way around the rotor so as not to warp it with different temps applied.) | + | * This one was set inside a charcoal grill with charcoal laid in a circle around it. The best way to do this is wait until the rotor has turned color completely. Then work quickly but carefully. Once the rotor reaches temperature, it begines to turn color rather quickly.((Vanmor of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666986&highlight=stator+repair)) \\ (Note: Best to place the charcoal all the way around the rotor so as not to warp it with different temps applied.) |
| |{{:techtalk:ref:priclutch:removing_rotor_magnets_1_by_vanmor.jpg?direct&300|}}|{{:techtalk:ref:priclutch:removing_rotor_magnets_2_by_vanmor.jpg?direct&300|}}| | |{{:techtalk:ref:priclutch:removing_rotor_magnets_1_by_vanmor.jpg?direct&300|}}|{{:techtalk:ref:priclutch:removing_rotor_magnets_2_by_vanmor.jpg?direct&300|}}| | ||
