Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:priclutch01 [2018/06/17 05:00] hippysmack [Removing the Magnets] |
techtalk:ref:priclutch01 [2018/06/17 05:01] hippysmack [Removing the Magnets] |
||
|---|---|---|---|
| Line 38: | Line 38: | ||
| * A heat gun has been used successfully on the outside of the hub ((juzyHD of the XLFORUM http://xlforum.net/forums/showthread.php?t=2000061&highlight=splines+hub)) adjacent to each magnet removed. | * A heat gun has been used successfully on the outside of the hub ((juzyHD of the XLFORUM http://xlforum.net/forums/showthread.php?t=2000061&highlight=splines+hub)) adjacent to each magnet removed. | ||
| - | * A torch (propane or whatever) should work better and faster. However, don't get it too hot or the magnet and the properties thereof could be ruined. Use a big screwdriver or small pry bar to LIGHTLY PRY the magnets loose or you will break them. TAKE YOUR TIME !!! ((Vanmor of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666986&highlight=stator+repair)) | + | * A torch (propane or whatever) should work better and faster. However, don't get it too hot or the magnet and the properties thereof could be ruined. \\ Use a big screwdriver or small pry bar to LIGHTLY PRY the magnets loose or you will break them. TAKE YOUR TIME !!! ((Vanmor of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666986&highlight=stator+repair)) |
| * You can put it in an oven at 400*, you want to heat it evenly as spot heating can cause distortion. The magnets are brittle so be careful. ((bustert of the XLFORUM http://xlforum.net/forums/showthread.php?t=2000061&highlight=splines+hub&page=2)) | * You can put it in an oven at 400*, you want to heat it evenly as spot heating can cause distortion. The magnets are brittle so be careful. ((bustert of the XLFORUM http://xlforum.net/forums/showthread.php?t=2000061&highlight=splines+hub&page=2)) | ||
| - | * This one was set inside a charcoal grill with charcoal laid in a circle around it. The best way to do this is wait until the rotor has turned color completely. Then work quickly but carefully. Once the rotor reaches temperature, it begines to turn color rather quickly.((Vanmor of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666986&highlight=stator+repair)) \\ (Note: Best to place the charcoal all the way around the rotor so as not to warp it with different temps applied.) | + | * This one was set inside a charcoal grill with charcoal laid in a circle around it. The best way to do this is wait until the rotor has turned color completely. \\ Then work quickly but carefully. Once the rotor reaches temperature, it begines to turn color rather quickly.((Vanmor of the XLFORUM http://xlforum.net/forums/showthread.php?t=1666986&highlight=stator+repair)) \\ (Note: Best to place the charcoal all the way around the rotor so as not to warp it with different temps applied.) |
| |{{:techtalk:ref:priclutch:removing_rotor_magnets_1_by_vanmor.jpg?direct&300|}}|{{:techtalk:ref:priclutch:removing_rotor_magnets_2_by_vanmor.jpg?direct&300|}}| | |{{:techtalk:ref:priclutch:removing_rotor_magnets_1_by_vanmor.jpg?direct&300|}}|{{:techtalk:ref:priclutch:removing_rotor_magnets_2_by_vanmor.jpg?direct&300|}}| | ||
