Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:svcproc9a [2024/05/01 17:26] hippysmack ↷ Page name changed from techtalk:ref:svcproc9a to techtalk:ref:svcproc9g |
techtalk:ref:svcproc9a [2024/05/01 18:31] hippysmack [1965 XLCH Transmission Assembly] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
| + | ====== REF: Service Procedures 9A ====== | ||
| + | \\ | ||
| + | ====== 1965 XLCH Transmission Assembly ====== | ||
| + | Article by scottericsonon of the XLForum ((https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/85677-transmission-assembly-tutorial-w-pics?t=657134)) \\ | ||
| + | A used transmission bought from Ebay was disassembled and the parts swapped over to the original trapdoor. \\ | ||
| + | The used transmission had all Andrews gears as well as the mainshaft and countershaft. \\ | ||
| + | I put new main and countershaft bearings in my trapdoor so I could reuse it so I know everything will line up with my case. \\ | ||
| + | |||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_andrews_gears_1_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_andrews_gears_2_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_andrews_gears_3_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_andrews_gears_4_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_andrews_gears_5_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | |||
| + | Empty trapdoor. \\ | ||
| + | I should note that while it was empty, I DID punch out the countershaft oiler plug so I can set endplay later. \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_trapdoor_1_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | |||
| + | Clutch gear with new bearing loaded into trap. \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_trapdoor_2_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_trapdoor_3_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | |||
| + | Mainshaft loaded in. You WILL have to pull it back apart again but I wanted to get the trans loaded just so I could see how everything fit together before I put the shift forks in. \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_mainshaft_loaded_1_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_mainshaft_loaded_2_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | \\ | ||
| + | |||
| + | \\ | ||
| + | |||
| + | \\ | ||
| + | |||
| + | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
