Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:svcproc9a [2024/05/01 20:52] hippysmack [1965 XLCH Transmission Assembly] |
techtalk:ref:svcproc9a [2024/05/02 00:54] hippysmack [1965 XLCH Transmission Assembly] |
||
---|---|---|---|
Line 63: | Line 63: | ||
\\ | \\ | ||
+ | Checking C/S clearance. I have .006" \\ | ||
+ | Don't mind my redneck setup. I'm just a poor bastard trying to do shit on a budget. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic12_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic13_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic14_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic15_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | Putting some pressure on the M/S to emulate the clutch being there and engaged. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic16_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic17_by_scottericsonon.jpg?direct&400|}} \\ | ||
\\ | \\ | ||
+ | |||
+ | (L) Checking the M/S endplay. I have .006" \\ | ||
+ | (R) Grab your shift shaft and slide it into its home making sure to have it level so it will go into it's pocket on the trans. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic18_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic19_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | |||
+ | Grab your M/S rollers making sure to COUNT THEM so you know you have all 23. \\ | ||
+ | Goo up the race and your C/S bearing and put all 23 rollers into place. \\ | ||
+ | MAKE SURE you put the flat washer in between the circlip and your bearing rollers!! | ||
+ | Did you check that it was there? Good...now check again. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic20_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic21_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | |||
+ | |||
+ | I greased up the rollers too so they would stick real well for me. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic22_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic23_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | |||
+ | (L) Cross your fingers and slide the trans in. If it's in right it should ALMOST seat by hand. \\ | ||
+ | At least it should start on the dowels. If not, try wiggling it some. It will line up. \\ | ||
+ | Get your bolts in tightening each of them a little at a time so that your trapdoor goes in straight. \\ | ||
+ | Then when they're all tight, pull them one at a time and put a dab of Loctite on them. \\ | ||
+ | (R) Ok, next step. Grab all your kickstart stuff. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic24_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic25_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | |||
+ | Slide the clutch shaft parts on with the collar first then the spring and the gear. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic26_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic27_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | |||
+ | (L) I thought sure I took one with the starter crank gear too but can seem to find it now. \\ | ||
+ | ANYHOW install that it's tabbed lock washer and the nut tighten it up and fold over one of the lock tabs. \\ | ||
+ | Get your primary shoe in with one bolt just to hold it in place while you're putting the chain etc in. \\ | ||
+ | (I put a new plastic shoe on mine obviously) \\ | ||
+ | (R) Gather up your primary chain, crankshaft gear and clutch basket. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic28_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic29_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | |||
+ | (L) This would be an EXCELLENT time to test your kickstarter to make sure it functions correctly. \\ | ||
+ | Just put the clutch basket in place and hold in with your hand as your helper. \\ | ||
+ | (or yourself if you can reach) cranks the kick thru one cycle. \\ | ||
+ | Now get the basket back in along with the primary chain and crank sprocket. \\ | ||
+ | Get the crank nut and the clutch hub in tightened up (150 lb/ft ). \\ | ||
+ | Make sure you fold over a lock tab on your clutch hub nut. \\ | ||
+ | Crank gear nut is 1-1/4" while the clutch basket is 1-1/2". \\ | ||
+ | (R) gather up your clutch parts. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic30_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic31_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | |||
+ | I had pulled the whole clutch as an assembly like this and left all the plates stacked while they were out. \\ | ||
+ | Made the install VERY easy as all I had to do was flip the stack over and put in pieces one at a time. \\ | ||
+ | Get the springs in the basket and grab your clutch release disk. \\ | ||
+ | Then get your spring compressor started and sneak the clutch release disk down behind it. \\ | ||
+ | (R) AS SOON AS you can get the locknuts started with 3 or 4 threads get them on there so the clutch isn't a loaded gun anymore. \\ | ||
+ | Go ahead and get those all tightened up and remove your spring compressor. \\ | ||
+ | It should be noted here that I have a 75 and as a result I have the spacers. \\ | ||
+ | If you have a different year (I think pre74), you don't want to just tighten up those nuts. \\ | ||
+ | There's a certain spacing they have to be at. \\ | ||
+ | Once your compressor is out of the way, slap the bolt in the lower hole of the primary adjuster. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic32_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic33_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | |||
+ | (L) Measure your primary chain slop and get that set to specs. \\ | ||
+ | Then go ahead and button up the rest of the adjuster making sure you double check slack after all your pieces are in and tight. \\ | ||
+ | (R) Ok, now let's move over to the right side of the bike for a bit. \\ | ||
+ | Grab your drive sprocket, a tabbed washer for that and it's nut and a 1-1/4" socket. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic34_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic35_by_scottericsonon.jpg?direct&400|}} \\ | ||
+ | \\ | ||
+ | |||
+ | Get that stuff on and tightened up remembering to fold the lock tabs over. \\ | ||
+ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic36_by_scottericsonon.jpg?direct&400|}} \\ | ||
\\ | \\ |