Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:svcproc9a [2024/05/01 21:17] hippysmack [1965 XLCH Transmission Assembly] |
techtalk:ref:svcproc9a [2024/05/01 23:59] hippysmack [1965 XLCH Transmission Assembly] |
||
|---|---|---|---|
| Line 66: | Line 66: | ||
| Don't mind my redneck setup. I'm just a poor bastard trying to do shit on a budget. \\ | Don't mind my redneck setup. I'm just a poor bastard trying to do shit on a budget. \\ | ||
| {{:techtalk:ref:svcproc:1965_xlch_tranny_pic12_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic13_by_scottericsonon.jpg?direct&400|}} \\ | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic12_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic13_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic14_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic15_by_scottericsonon.jpg?direct&400|}} \\ | ||
| \\ | \\ | ||
| + | |||
| + | Putting some pressure on the M/S to emulate the clutch being there and engaged. \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic16_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic17_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | |||
| + | (L) Checking the M/S endplay. I have .006" \\ | ||
| + | (R) Grab your shift shaft and slide it into its home making sure to have it level so it will go into it's pocket on the trans. \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic18_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic19_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | |||
| + | Grab your M/S rollers making sure to COUNT THEM so you know you have all 23. \\ | ||
| + | Goo up the race and your C/S bearing and put all 23 rollers into place. \\ | ||
| + | MAKE SURE you put the flat washer in between the circlip and your bearing rollers!! | ||
| + | Did you check that it was there? Good...now check again. \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic20_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic21_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | |||
| + | |||
| + | I greased up the rollers too so they would stick real well for me. \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic22_by_scottericsonon.jpg?direct&400|}} {{:techtalk:ref:svcproc:1965_xlch_tranny_pic23_by_scottericsonon.jpg?direct&400|}} \\ | ||
| + | \\ | ||
| + | |||
| + | Cross your fingers and slide the trans in. If it's in right it should ALMOST seat by hand. \\ | ||
| + | At least it should start on the dowels. If not, try wiggling it some. It will line up. \\ | ||
| + | Get your bolts in tightening each of them a little at a time so that your trapdoor goes in straight. \\ | ||
| + | Then when they're all tight, pull them one at a time and put a dab of Loctite on them. \\ | ||
| + | {{:techtalk:ref:svcproc:1965_xlch_tranny_pic24_by_scottericsonon.jpg?direct&400|}} \\ | ||
| \\ | \\ | ||
