Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:tools026 [2020/05/22 23:14] hippysmack [Field Calibration] |
techtalk:ref:tools026 [2020/05/24 03:14] hippysmack [Field Calibration] |
||
|---|---|---|---|
| Line 101: | Line 101: | ||
| The procedure below is a simple adjustment to correct a situation where the end nut has been allowed to turn and change the tension. \\ | The procedure below is a simple adjustment to correct a situation where the end nut has been allowed to turn and change the tension. \\ | ||
| - | This just helps to change the tension back. Use the information at your own risk. \\ | + | This just helps to change the tension back. Some have used this procedure and seem to like it. \\ |
| + | Use the information at your own risk. \\ | ||
| - **Turn the adjusting sleeve down to the lowest setting**. | - **Turn the adjusting sleeve down to the lowest setting**. | ||
| Line 111: | Line 112: | ||
| - **Repeat this calibration procedure until you get the wrench to click on the length mark as in the test check above**. | - **Repeat this calibration procedure until you get the wrench to click on the length mark as in the test check above**. | ||
| - | {{:techtalk:ref:tools:torque_wrench_calibration_15_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:torque_wrench_calibration_16_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:torque_wrench_calibration_17_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | + | {{:techtalk:ref:tools:torque_wrench_calibration_15_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:torque_wrench_calibration_160_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:torque_wrench_calibration_17_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ |
| On the test wrench, the bushing was turned counterclockwise originally and the wrench clicked even farther toward the handle end once tested. \\ | On the test wrench, the bushing was turned counterclockwise originally and the wrench clicked even farther toward the handle end once tested. \\ | ||
| Line 119: | Line 120: | ||
| {{:techtalk:ref:tools:torque_wrench_calibration_18_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)){{:techtalk:ref:tools:torque_wrench_calibration_19_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)){{:techtalk:ref:tools:torque_wrench_calibration_20_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:ref:tools:torque_wrench_calibration_18_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)){{:techtalk:ref:tools:torque_wrench_calibration_19_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)){{:techtalk:ref:tools:torque_wrench_calibration_20_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| + | **Related videos:** \\ | ||
| + | * [[https://www.youtube.com/watch?v=8HGO9Vv9eDE|Torque Wrench Stopped Clicking FIX and Calibration]] | ||
| + | * [[https://www.youtube.com/watch?v=XaqBA-xSGbc|Calibrate a Torque Wrench with a $5 Luggage Scale]] | ||
| + | |||
| + | |||
| \\ | \\ | ||
