Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:tools103 [2019/05/21 17:59] hippysmack [Steel angle fixture] |
techtalk:ref:tools103 [2019/10/18 22:03] hippysmack [Pulling the Race] |
||
---|---|---|---|
Line 60: | Line 60: | ||
|{{techtalk:ref:tools:flywheel_race_puller_by_treybutcher.jpg?direct&300|}}| | |{{techtalk:ref:tools:flywheel_race_puller_by_treybutcher.jpg?direct&300|}}| | ||
^ **Flywheel Race Puller** ((photo by TreyButcher of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=14)) ^ | ^ **Flywheel Race Puller** ((photo by TreyButcher of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=14)) ^ | ||
- | + | ||
+ | ===== Race, Spacer and Oil Seal Press ===== | ||
+ | |||
+ | {{:techtalk:ref:tools:installing_race-spacer-_oil_seal_onto_crank_shaft_1_by_aussiegazza.jpg?direct&300|}} ((photo by AussieGazza of the XLFORUM http://xlforum.net/forums/showthread.php?t=692835&page=14)) {{:techtalk:ref:tools:installing_race-spacer-_oil_seal_onto_crank_shaft_2_by_aussiegazza.jpg?direct&300|}} ((photo by AussieGazza of the XLFORUM http://xlforum.net/forums/showthread.php?t=692835&page=14)) \\ | ||
+ | |||
+ | {{:techtalk:ref:tools:installing_race-spacer-_oil_seal_onto_crank_shaft_3_by_aussiegazza.jpg?direct&300|}} ((photo by AussieGazza of the XLFORUM http://xlforum.net/forums/showthread.php?t=692835&page=14)) {{:techtalk:ref:tools:installing_race-spacer-_oil_seal_onto_crank_shaft_4_by_aussiegazza.jpg?direct&300|}} ((photo by AussieGazza of the XLFORUM http://xlforum.net/forums/showthread.php?t=692835&page=14)) | ||
===== Flywheel / Crankshaft Balancing - Truing ===== | ===== Flywheel / Crankshaft Balancing - Truing ===== | ||
Line 79: | Line 84: | ||
|Here is another way to true flywheels in a small Myford lathe that has only a 4.5" swing that won't fit Harley flywheels. \\ Two offset pieces made from some flat half-inch thick bar and some half-inch round bar.||| | |Here is another way to true flywheels in a small Myford lathe that has only a 4.5" swing that won't fit Harley flywheels. \\ Two offset pieces made from some flat half-inch thick bar and some half-inch round bar.||| | ||
^ **Truing flywheels on center in a lathe via offset jigs** ((photos by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586)) ^^^ | ^ **Truing flywheels on center in a lathe via offset jigs** ((photos by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586)) ^^^ | ||
+ | |||
+ | |{{:techtalk:ref:tools:truing_flywheels_in_a_lathe_by_aussiegazz.jpg?direct&300|}}| | ||
+ | ^ **Truing flywheels on center in a lathe with \\ no offset jigs** ((photo by AussieGazza of the XLFORUM http://xlforum.net/forums/showthread.php?t=692835&page=9)) ^ | ||
+ | |||
===== Crankshaft / Flywheel Installation ===== | ===== Crankshaft / Flywheel Installation ===== | ||