Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revision Both sides next revision
techtalk:ref:tools107 [2019/01/20 01:59]
hippysmack [Reamers]
techtalk:ref:tools107 [2019/05/28 04:41]
hippysmack [Bushing Removal]
Line 1: Line 1:
 [[:​techtalk:​menu|{{ ​ :​techtalk:​gototechnicalmenu.jpg|}}]] [[:​techtalk:​menu|{{ ​ :​techtalk:​gototechnicalmenu.jpg|}}]]
 ====== REF: Tools - 107 ====== ====== REF: Tools - 107 ======
-====== Cam Bushing Removal Tools ====== +====== Cam Bushing ​Measuring / Removal ​/ Installation ​Tools ====== 
-===== Bushing Removal =====+====== Measuring the Bushings ====== 
 + 
 + 
 +|  Measuring Cam Bushinhgs. ((photos by AussieGazza of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=692835&​page=5)) ​ ||| 
 +|{{:​techtalk:​ref:​tools:​measuring_cam_bushings_1_by_aussiegazza.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​measuring_cam_bushings_2_by_aussiegazza.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​measuring_cam_bushings_3_by_aussiegazza.jpg?​direct&​300|}}| 
 + 
 +====== Bushing Removal ​======
  
  
Line 10: Line 16:
 |{{:​techtalk:​ref:​tools:​98_1200_cam_bushing_removal_2_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​tools:​cam_bushing_installer_2_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​tools:​cam_bushing_installer_1_by_hippysmack.jpg?​direct&​300|}}| |{{:​techtalk:​ref:​tools:​98_1200_cam_bushing_removal_2_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​tools:​cam_bushing_installer_2_by_hippysmack.jpg?​direct&​300|}}|{{techtalk:​ref:​tools:​cam_bushing_installer_1_by_hippysmack.jpg?​direct&​300|}}|
  
-|Also check local auto parts stores for a pilot bearing puller. ​\\ This works basically ​the same as the slide hammer except it pulls the bushings out instead of knocking them out. ((photos by 62 Ironhead of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1717904&​page=2))||| +|Check local auto parts stores for a pilot bearing puller. ​((photo by 62 Ironhead of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1717904&​page=2))| 
-|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_1_by_62_ironhead.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_2_by_62_ironhead.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_3_by_62_ironhead.jpg?​direct&​300|}}|+|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_1_by_62_ironhead.jpg?​direct&​300|}}| 
 + 
 +|This works basically ​like the slide hammer except it pulls the bushings out instead of knocking them out. ((photos by 62 Ironhead of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1717904&​page=2)) ||For smaller bushings, grind the back of the jaws a \\ little so they close more to fit the smaller space. ((photo by decman of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​t=1793066&​page=7))
 +|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_2_by_62_ironhead.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_3_by_62_ironhead.jpg?​direct&​300|}}|{{:​techtalk:​ref:​tools:​pilot_bearing_puller_by_decman.jpg?​direct&​300|}}|
  
 ===== Modified Cover for Reaming ===== ===== Modified Cover for Reaming =====
Line 22: Line 31:
 ===== Reamers ===== ===== Reamers =====
 **Cam cover bushings**: \\ **Cam cover bushings**: \\
-The reamers for the cam cover need to be chamfered (chucking) reamers. \\+The reamers for the cam cover bushings (#1, #3 and #4) need to be chamfered (chucking) reamers. \\
 The ends have a short chamfer that will enter the blind bushing bore and not hit the rear of the bore before finished cutting the bushings. \\ The ends have a short chamfer that will enter the blind bushing bore and not hit the rear of the bore before finished cutting the bushings. \\
 The reamer for #2 cam can be a tapered bridge reamer on models with nosecone ignitions. \\ The reamer for #2 cam can be a tapered bridge reamer on models with nosecone ignitions. \\
Line 45: Line 54:
 Case bushing reamer size: \\ Case bushing reamer size: \\
  
-11/16" for #1-#4 cam bushings. \\+11/16" for #1 thru #4 cam bushings. \\
  
 |  Cam bushing reamers ((photo by decman of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​postid=5016753)) ​ | |  Cam bushing reamers ((photo by decman of the XLFORUM http://​xlforum.net/​forums/​showthread.php?​postid=5016753)) ​ |