Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:tools107 [2019/05/28 04:34] hippysmack [Cam Bushing Removal Tools] |
techtalk:ref:tools107 [2019/10/19 04:09] hippysmack [Bushing Removal] |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ====== REF: Tools - 107 ====== | ====== REF: Tools - 107 ====== | ||
| ====== Cam Bushing Measuring / Removal / Installation Tools ====== | ====== Cam Bushing Measuring / Removal / Installation Tools ====== | ||
| - | ===== Bushing Removal ===== | + | \\ |
| + | ====== #2 Cam Gear Press ====== | ||
| + | A Gear puller shaft attached to a bearing separator for pressing the gear on #2 cam. \\ | ||
| + | |Gear press for #2 cam gear. ((photo by jstoll of the XLFORUM http://xlforum.net/forums/showthread.php?t=1961921))| | ||
| + | |{{:techtalk:ref:tools:gear_press_for_2_cam_by_jstoll.jpg?direct&250|}}| | ||
| + | |||
| + | ====== Measuring the Bushings ====== | ||
| + | |||
| + | |||
| + | | Measuring Cam Bushinhgs. ((photos by AussieGazza of the XLFORUM http://xlforum.net/forums/showthread.php?t=692835&page=5)) ||| | ||
| + | |{{:techtalk:ref:tools:measuring_cam_bushings_1_by_aussiegazza.jpg?direct&300|}}|{{:techtalk:ref:tools:measuring_cam_bushings_2_by_aussiegazza.jpg?direct&300|}}|{{:techtalk:ref:tools:measuring_cam_bushings_3_by_aussiegazza.jpg?direct&300|}}| | ||
| + | |||
| + | ====== Bushing Removal ====== | ||
| Line 15: | Line 27: | ||
| |This works basically like the slide hammer except it pulls the bushings out instead of knocking them out. ((photos by 62 Ironhead of the XLFORUM http://xlforum.net/forums/showthread.php?t=1717904&page=2)) ||For smaller bushings, grind the back of the jaws a \\ little so they close more to fit the smaller space. ((photo by decman of the XLFORUM http://xlforum.net/forums/showthread.php?t=1793066&page=7))| | |This works basically like the slide hammer except it pulls the bushings out instead of knocking them out. ((photos by 62 Ironhead of the XLFORUM http://xlforum.net/forums/showthread.php?t=1717904&page=2)) ||For smaller bushings, grind the back of the jaws a \\ little so they close more to fit the smaller space. ((photo by decman of the XLFORUM http://xlforum.net/forums/showthread.php?t=1793066&page=7))| | ||
| |{{:techtalk:ref:tools:pilot_bearing_puller_2_by_62_ironhead.jpg?direct&300|}}|{{:techtalk:ref:tools:pilot_bearing_puller_3_by_62_ironhead.jpg?direct&300|}}|{{:techtalk:ref:tools:pilot_bearing_puller_by_decman.jpg?direct&300|}}| | |{{:techtalk:ref:tools:pilot_bearing_puller_2_by_62_ironhead.jpg?direct&300|}}|{{:techtalk:ref:tools:pilot_bearing_puller_3_by_62_ironhead.jpg?direct&300|}}|{{:techtalk:ref:tools:pilot_bearing_puller_by_decman.jpg?direct&300|}}| | ||
| + | |||
| + | ====== Bushing Installation ====== | ||
| ===== Modified Cover for Reaming ===== | ===== Modified Cover for Reaming ===== | ||
