Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:tools107 [2019/10/19 04:15] hippysmack [Bushing Installation] |
techtalk:ref:tools107 [2019/10/19 04:41] hippysmack [Bushing Removal] |
||
---|---|---|---|
Line 27: | Line 27: | ||
|This works basically like the slide hammer except it pulls the bushings out instead of knocking them out. ((photos by 62 Ironhead of the XLFORUM http://xlforum.net/forums/showthread.php?t=1717904&page=2)) ||For smaller bushings, grind the back of the jaws a \\ little so they close more to fit the smaller space. ((photo by decman of the XLFORUM http://xlforum.net/forums/showthread.php?t=1793066&page=7))| | |This works basically like the slide hammer except it pulls the bushings out instead of knocking them out. ((photos by 62 Ironhead of the XLFORUM http://xlforum.net/forums/showthread.php?t=1717904&page=2)) ||For smaller bushings, grind the back of the jaws a \\ little so they close more to fit the smaller space. ((photo by decman of the XLFORUM http://xlforum.net/forums/showthread.php?t=1793066&page=7))| | ||
|{{:techtalk:ref:tools:pilot_bearing_puller_2_by_62_ironhead.jpg?direct&300|}}|{{:techtalk:ref:tools:pilot_bearing_puller_3_by_62_ironhead.jpg?direct&300|}}|{{:techtalk:ref:tools:pilot_bearing_puller_by_decman.jpg?direct&300|}}| | |{{:techtalk:ref:tools:pilot_bearing_puller_2_by_62_ironhead.jpg?direct&300|}}|{{:techtalk:ref:tools:pilot_bearing_puller_3_by_62_ironhead.jpg?direct&300|}}|{{:techtalk:ref:tools:pilot_bearing_puller_by_decman.jpg?direct&300|}}| | ||
+ | |||
+ | **Homemade bushing remover**: \\ | ||
+ | The puller is made from 1" ID black pipe and 1/2"-13 threaded rod. You tap the flex head-puller head through the cam bearing. \\ | ||
+ | The little nub puller with a collar that you knock into the bearing is made from 3/4" rod. Then screw the rod into the head to tighten the jaws. \\ | ||
+ | Then place the collar over the rod and nut to start the pulling. \\ | ||
+ | |||
+ | 4 grooves were cut into the end for flex / compression to push through the bearing. \\ | ||
+ | Then it was center drilled 7/16" and tapped 1/2"-13 and the slots were cut with a 3/16" end mill. \\ | ||
+ | The threaded rod causes outward pressure on the jaws of the head when pulled. \\ | ||
+ | |{{:techtalk:ref:tools:homemade_cam_bushing_tools_1_by_fergerburger.jpg?direct&300|}}|{{:techtalk:ref:tools:homemade_cam_bushing_tools_2_by_fergerburger.jpg?direct&300|}}|{{:techtalk:ref:tools:homemade_cam_bushing_tools_4_by_fergerburger.jpg?direct&300|}}| | ||
+ | |||
+ | |{{:techtalk:ref:tools:homemade_cam_bushing_tools_5_by_fergerburger.jpg?direct&300|}}|{{:techtalk:ref:tools:homemade_cam_bushing_tools_6_by_fergerburger.jpg?direct&300|}}|{{:techtalk:ref:tools:homemade_cam_bushing_tools_7_by_fergerburger.jpg?direct&300|}}| | ||
====== Bushing Installation ====== | ====== Bushing Installation ====== | ||
Line 32: | Line 44: | ||
Below are a couple homemade tools for installing the bushings. A knocking rod and a compression plate. \\ | Below are a couple homemade tools for installing the bushings. A knocking rod and a compression plate. \\ | ||
- | {{:techtalk:ref:tools:homemade_cam_bushing_tools_3_by_fergerburger.jpg?direct&300|}} ((photo by fergerburger of the XLFORUM http://xlforum.net/forums/showthread.php?t=1349714)) | + | The knocker rod is made from 1" aluminum bar stock with a .030" shoulder to recess into the bearing, .030" into the case. ((fergerburger of the XLFORUM http://xlforum.net/forums/showthread.php?t=1349714)) \\ |
+ | |||
+ | The compression plate is made from a scrap steel plate. The bolts screw in to push the bushings in place. See the [[techtalk:ref:tools107#reverse_engineered_cam_bushing_installer|build pics]] below by Hippysmack. \\ | ||
+ | |||
+ | {{:techtalk:ref:tools:homemade_cam_bushing_tools_3_by_fergerburger.jpg?direct&300|}} ((photo by fergerburger of the XLFORUM http://xlforum.net/forums/showthread.php?t=1349714)) {{techtalk:ref:tools:cam_bushing_installer_41_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{techtalk:ref:tools:cam_bushing_installer_39_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
===== Modified Cover for Reaming ===== | ===== Modified Cover for Reaming ===== | ||