Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:tools110 [2019/02/16 01:27] hippysmack [Lift Riser / Adapter] |
techtalk:ref:tools110 [2019/07/03 22:35] hippysmack [Jack Stands] |
||
---|---|---|---|
Line 8: | Line 8: | ||
====== Bike Lifts / Jacks ====== | ====== Bike Lifts / Jacks ====== | ||
+ | ===== Jack Stands ===== | ||
+ | **Homemade Jack Stands**: \\ | ||
+ | These were made specifically for a bike with a center stand. ((Toejam503 of the XLFORUM http://xlforum.net/forums/showthread.php?p=5760229#post5760229)) \\ | ||
+ | With these you can lift the front wheel off the ground when doing tires, wheel bearings, forks, etc. \\ | ||
+ | On a bike without a center stand, you can use the kickstand as a pivot. \\ | ||
+ | These little stands can be placed, strategically, under the frame for stability while working. \\ | ||
+ | |||
+ | Base: 4.5" of 1"x2" C-channel iron. \\ | ||
+ | Shaft welded to center of base: Iron conduit 1" OD approx. 4" high. \\ | ||
+ | A 15/16" nut is welded to top of shaft. \\ | ||
+ | The nuts were welded to the base for stability of the assembly. \\ | ||
+ | However, you could add a nut (un-welded) on top of the that one for more adjustability. \\ | ||
+ | First, measure your individual clearance to get the overall (collapsed) height that you can use. \\ | ||
+ | The top is made from a threaded rod welded to metal C-channel (saddles). \\ | ||
+ | |||
+ | |{{:techtalk:ref:tools:homemade_jac_stands_1_by_toejam503.jpg?direct&300|}}|{{:techtalk:ref:tools:homemade_jac_stands_2_by_toejam503.jpg?direct&300|}}|{{:techtalk:ref:tools:homemade_jac_stands_3_by_toejam503.jpg?direct&300|}}| | ||
+ | ^ Homemade jack stands. ((photos by Toejam503 of the XLFORUM http://xlforum.net/forums/showthread.php?p=5760229#post5760229)) ^^^ | ||
+ | |||
+ | ---- | ||
+ | |||
+ | **Commercial Auto Jack Stands**: \\ | ||
|{{:techtalk:ref:tools:lift_stands_1_by_erik.jpg?direct&300|}}|{{:techtalk:ref:tools:lift_stands_2_by_erik.jpg?direct&300|}}| | |{{:techtalk:ref:tools:lift_stands_1_by_erik.jpg?direct&300|}}|{{:techtalk:ref:tools:lift_stands_2_by_erik.jpg?direct&300|}}| | ||
^ Lift stands ((photos by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=14)) ^^ | ^ Lift stands ((photos by Erik of the XLFORUM http://xlforum.net/forums/showthread.php?t=320342&page=14)) ^^ | ||
^Take the front or rear footpegs off and bolt them back upside down. \\ Then placed two axle stands under them.^^ | ^Take the front or rear footpegs off and bolt them back upside down. \\ Then placed two axle stands under them.^^ | ||
+ | |||
+ | ===== Lifts ===== | ||
+ | |||
|{{techtalk:ref:tools:bike_jack_by_bob_f.jpg?direct&300|}}|{{techtalk:ref:tools:bike_jack_by_loves_curves.jpg?direct&300|}}|{{techtalk:ref:tools:bike_lift_by_hopper.jpg?direct&300|}}| | |{{techtalk:ref:tools:bike_jack_by_bob_f.jpg?direct&300|}}|{{techtalk:ref:tools:bike_jack_by_loves_curves.jpg?direct&300|}}|{{techtalk:ref:tools:bike_lift_by_hopper.jpg?direct&300|}}| |