Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:tools115 [2018/05/22 23:52] hippysmack [4 Speed] |
techtalk:ref:tools115 [2018/11/06 23:14] hippysmack [5 Speed (1991-later)] |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| | **Clutch Hub Tool** ((photos by arkyboy of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=6)) || | | **Clutch Hub Tool** ((photos by arkyboy of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=6)) || | ||
| - | |Two pieces of timber screwed together, a piece of hardware store 1/4" UNC threaded rod cut in half and \\ some 1/4 nuts and washers. \\ It does not have the center screw like the factory tool. \\ Just tighten down the nuts on the threaded rod to compress the clutch springs. ((Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))| | + | |Two pieces of timber screwed together, some 1/4" \\ UNC threaded rod, 1/4" nuts and washers. It does not \\ have the center screw like the factory tool. Just tighten \\ down the nuts on the threaded rod to compress the \\ clutch springs. ((Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))| This one uses an auto harmonic balancer puller as \\ a center torque shaft| |
| - | |{{techtalk:ref:tools:clutch_compressor_tool_by_hopper.jpg?direct&500|}}| | + | |{{techtalk:ref:tools:clutch_compressor_tool_by_hopper.jpg?direct&300|}}|{{techtalk:ref:tools:clutch_spring_compressing_tool_by_ironmick.jpg?direct&300|}}|{{:techtalk:ref:tools:clutch_spring_compressor_by_tribulation.jpg?direct&200|}}| |
| - | |Clutch spring compressor ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586))| | + | | **Clutch spring compressor** ((photo by Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586)) | **Clutch spring compressor** ((photo by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?threadid=2023217)) | **Clutch spring compressor** ((photo by Tribulation of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=18)) | |
| - | + | ||
| - | |Similar to above but with an auto harmonic balancer puller as a center torque shaft| | + | |
| - | |{{techtalk:ref:tools:clutch_spring_compressing_tool_by_ironmick.jpg?direct&500|}}| | + | |
| - | |Clutch spring compressor ((photo by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?threadid=2023217))| | + | |
| ===== 5 Speed (1991-later) ===== | ===== 5 Speed (1991-later) ===== | ||
| Line 23: | Line 19: | ||
| {{:techtalk:ref:priclutch:91-later-clutchdiaphragm-compressiontool-1.jpg?600|}}\\ | {{:techtalk:ref:priclutch:91-later-clutchdiaphragm-compressiontool-1.jpg?600|}}\\ | ||
| + | |||
| + | {{:techtalk:ref:tools:clutch_spring_compressor_1_by_dirty_don.jpg?direct&300|}}{{:techtalk:ref:tools:clutch_spring_compressor_2_by_dirty_don.jpg?direct&300|}}{{:techtalk:ref:tools:clutch_spring_compressor_3_by_dirty_don.jpg?direct&300|}} ((photos by Dirty Don of the XLFORUM http://xlforum.net/forums/showthread.php?threadid=1608837)) | ||
| + | |||
| + | {{:techtalk:ref:tools:clutch_compression_tool_1_by_jt1200r.jpg?direct&300|}} {{:techtalk:ref:tools:clutch_compression_tool_2_by_jt1200r.jpg?direct&300|}} ((photos by Jt1200r of the XLFORUM http://xlforum.net/forums/showthread.php?t=49915&page=14)) | ||
| + | |||
| + | 3" PVC cap w/ 5/16"x24 bolt or all-thread, coupler, nut and washer. | ||
| + | {{:techtalk:ref:tools:clutch_spring_compressor_by_trainman.jpg?direct&300|}} ((photo by trainman of the XLFORUM)) {{:techtalk:ref:tools:clutch_spring_compressor_by_daytonasportster.jpg?direct&300|}} ((photo by DaytonaSportster of the XLFORUM http://xlforum.net/forums/showthread.php?t=1742779)) | ||
| {{:techtalk:ref:priclutch:91-later-clutchdiaphragm-compressiontool-2.jpg?600|}}\\ | {{:techtalk:ref:priclutch:91-later-clutchdiaphragm-compressiontool-2.jpg?600|}}\\ | ||
