Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:tools124 [2021/11/12 22:59] hippysmack [Evo Engine] |
techtalk:ref:tools124 [2021/11/12 23:18] hippysmack [Ironhead Engine] |
||
|---|---|---|---|
| Line 4: | Line 4: | ||
| ====== Ironhead Engine ====== | ====== Ironhead Engine ====== | ||
| - | * Keep the extender straight out in front of the wrench. Don't let it move out of line more than a ratchet click or two, otherwise it can affect the torque reading. ((Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=2)) \\ [[techtalk:ref:tools123#torque_socket_wrench_extensions_horizontal_with_the_wrench|Read more about torque value changes with the use of extensions here]]. | + | * Keep the extender straight out in front of the wrench. \\ Don't let it move out of line more than a ratchet click or two, otherwise it can affect the torque reading. ((Hopper of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=2)) |
| + | * If the extension is not used at a 90° angle from the wrench (as in the pics below), you'll need to recalculate torque before using. \\ [[techtalk:ref:tools123#torque_socket_wrench_extensions_horizontal_with_the_wrench|Read more about torque value changes with the use of extensions here]]. | ||
| |Torque rocker box bolts to 20 ft lbs. You can use a wrench cut down to 3 inches long and welded to a 3/8 drive socket to get in under the frame and torque those \\ rocker bolts to show 185 inch pounds on a 10 inch torque wrench, to give 240 at the bolt.||| | |Torque rocker box bolts to 20 ft lbs. You can use a wrench cut down to 3 inches long and welded to a 3/8 drive socket to get in under the frame and torque those \\ rocker bolts to show 185 inch pounds on a 10 inch torque wrench, to give 240 at the bolt.||| | ||
| Line 34: | Line 35: | ||
| However, it's best to only install the bolts to "snug", then use a 1/4" beam type torque wrench to finish bolt installation. \\ | However, it's best to only install the bolts to "snug", then use a 1/4" beam type torque wrench to finish bolt installation. \\ | ||
| - | * You can buy a three pack of gear ratchet inserts,(1/4”-3/8”-1/2”). \\ That turns the appropriate size gear ratchet into a “slimmer profile" ratchet that can be useful at times. | + | * You can buy a three pack of gear ratchet inserts,(1/4”-3/8”-1/2”). \\ That turns the appropriate size gear ratchet into a “slimmer profile" ratchet that can be useful at times. ((sportsterpaul of the XLFORUM http://xlforum.net/forums/showthread.php?p=5924506#post5924506)) |
| * A company called KATAR makes a wrench specifically for the Evo lower rocker box bolts. Made in the USA. \\ It's a reversible ratcheting box wrench with a deep well 7/16" socket. \\ This allows for removal or installation of the lower rocker box hex nut bolts (5/16" bolts with 7/16" hex heads). \\ It has a long handle and a short profile making it easier to get to the bolts. | * A company called KATAR makes a wrench specifically for the Evo lower rocker box bolts. Made in the USA. \\ It's a reversible ratcheting box wrench with a deep well 7/16" socket. \\ This allows for removal or installation of the lower rocker box hex nut bolts (5/16" bolts with 7/16" hex heads). \\ It has a long handle and a short profile making it easier to get to the bolts. | ||
