Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:tools127 [2019/09/12 04:34] hippysmack [General Cleaning and Stuck Gaskets] |
techtalk:ref:tools127 [2022/03/27 04:43] hippysmack [Jets] |
||
---|---|---|---|
Line 12: | Line 12: | ||
|{{:techtalk:ref:tools:bendix_carb_13_by_popgadget.jpg?direct&200|}}|{{:techtalk:ref:tools:bendix_carb_12_by_popgadget.jpg?direct&200|}}| | |{{:techtalk:ref:tools:bendix_carb_13_by_popgadget.jpg?direct&200|}}|{{:techtalk:ref:tools:bendix_carb_12_by_popgadget.jpg?direct&200|}}| | ||
+ | |||
+ | |"Intake Manifold Wrench" - 'Z' shaped Allen wrench ((photo by Phillober of the XLFORUM http://xlforum.net/forums/showthread.php?t=1122547)) \\ Made for this purpose, available online ($10-$20)|This is a Bondhus Driver ((photo by biknut of the XLFORUM http://xlforum.net/forums/showthread.php?p=2292820)) \\ (basically a ball end Allen wrench with a handle)| | ||
+ | |{{:techtalk:ref:tools:mainiflod_wrench_by_phllober.jpg?direct&300|}}|{{:techtalk:ref:tools:bondhus_driver_by_biknut.jpg?direct&300|}}| | ||
+ | |||
+ | | Bondhus Allen and T-handle wrenches for getting to the manifold bolts. ((photos by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1399324)) || | ||
+ | |{{:techtalk:ref:tools:bondhus_allen_wrenches_by_aswracing.jpg?direct&300|}}|{{:techtalk:ref:tools:t_handle_ball_end_hex_wrench_by_aswracing.jpg?direct&300|}}| | ||
===== Parts Storage ===== | ===== Parts Storage ===== | ||
Line 80: | Line 86: | ||
The old bowl is to the left in the pic below and represents the condition of the carb before soaking. \\ | The old bowl is to the left in the pic below and represents the condition of the carb before soaking. \\ | ||
The carb was dunked in a container of Pinesol a little while (not overnight) and then touched up with a tootbrush and a final dunk. \\ | The carb was dunked in a container of Pinesol a little while (not overnight) and then touched up with a tootbrush and a final dunk. \\ | ||
+ | Then wash thoroughly with warm / hot soapy water and blow all the passages out really well. \\ | ||
+ | Reassemble carb and install. \\ | ||
All passages were blown out with compressed air. | All passages were blown out with compressed air. | ||
| Bendix cleaned with Pinesol. ((photo by drhach of the XLFORUM http://xlforum.net/forums/showthread.php?t=983964&page=3)) | | | Bendix cleaned with Pinesol. ((photo by drhach of the XLFORUM http://xlforum.net/forums/showthread.php?t=983964&page=3)) | | ||
|{{:techtalk:ref:carb:pinesoled_a_bendix_by_drhach.jpg?direct&300|}}| | |{{:techtalk:ref:carb:pinesoled_a_bendix_by_drhach.jpg?direct&300|}}| | ||
+ | |||
+ | ==== General Screw Removal ==== | ||
+ | |||
==== Jets ==== | ==== Jets ==== | ||
Line 98: | Line 109: | ||
- | ===== Intake Manifold ===== | ||
- | |"Intake Manifold Wrench" - 'Z' shaped Allen wrench ((photo by Phillober of the XLFORUM http://xlforum.net/forums/showthread.php?t=1122547)) \\ Made for this purpose, available online ($10-$20)|This is a Bondhus Driver ((photo by biknut of the XLFORUM http://xlforum.net/forums/showthread.php?p=2292820)) \\ (basically a ball end Allen wrench with a handle)| | + | ===== Sleeve for Tuning Air / Fuel Mixture ===== |
- | |{{:techtalk:ref:tools:mainiflod_wrench_by_phllober.jpg?direct&300|}}|{{:techtalk:ref:tools:bondhus_driver_by_biknut.jpg?direct&300|}}| | + | This is a Kevlar sleeve from NAPA and cost about 8 bucks. \\ |
+ | |It helps to keep from burning your skin on the exhaust while the A/F mix per [[techtalk:evo:carb02#the_idle_drop_method_idm|The Idle Drop Method]]. ((photos by rocketmangb of the XLFORUM http://xlforum.net/forums/showthread.php?t=1820463&page=10))|| | ||
+ | |{{:techtalk:ref:tools:carb_adjusting_sleeve_1_by_rocketmangb.jpg?direct&300|}}|{{:techtalk:ref:tools:carb_adjusting_sleeve_2_by_rocketmangb.jpg?direct&300|}}| | ||