Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:tools127 [2019/09/19 04:39] hippysmack [Sleeve for Tuning Air / Fuel Mixture] |
techtalk:ref:tools127 [2022/03/27 05:22] hippysmack [General Screw Removal] |
||
|---|---|---|---|
| Line 12: | Line 12: | ||
| |{{:techtalk:ref:tools:bendix_carb_13_by_popgadget.jpg?direct&200|}}|{{:techtalk:ref:tools:bendix_carb_12_by_popgadget.jpg?direct&200|}}| | |{{:techtalk:ref:tools:bendix_carb_13_by_popgadget.jpg?direct&200|}}|{{:techtalk:ref:tools:bendix_carb_12_by_popgadget.jpg?direct&200|}}| | ||
| + | |||
| + | |"Intake Manifold Wrench" - 'Z' shaped Allen wrench ((photo by Phillober of the XLFORUM http://xlforum.net/forums/showthread.php?t=1122547)) \\ Made for this purpose, available online ($10-$20)|This is a Bondhus Driver ((photo by biknut of the XLFORUM http://xlforum.net/forums/showthread.php?p=2292820)) \\ (basically a ball end Allen wrench with a handle)| | ||
| + | |{{:techtalk:ref:tools:mainiflod_wrench_by_phllober.jpg?direct&300|}}|{{:techtalk:ref:tools:bondhus_driver_by_biknut.jpg?direct&300|}}| | ||
| + | |||
| + | | Bondhus Allen and T-handle wrenches for getting to the manifold bolts. ((photos by aswracing of the XLFORUM http://xlforum.net/forums/showthread.php?t=1399324)) || | ||
| + | |{{:techtalk:ref:tools:bondhus_allen_wrenches_by_aswracing.jpg?direct&300|}}|{{:techtalk:ref:tools:t_handle_ball_end_hex_wrench_by_aswracing.jpg?direct&300|}}| | ||
| ===== Parts Storage ===== | ===== Parts Storage ===== | ||
| Line 85: | Line 91: | ||
| | Bendix cleaned with Pinesol. ((photo by drhach of the XLFORUM http://xlforum.net/forums/showthread.php?t=983964&page=3)) | | | Bendix cleaned with Pinesol. ((photo by drhach of the XLFORUM http://xlforum.net/forums/showthread.php?t=983964&page=3)) | | ||
| |{{:techtalk:ref:carb:pinesoled_a_bendix_by_drhach.jpg?direct&300|}}| | |{{:techtalk:ref:carb:pinesoled_a_bendix_by_drhach.jpg?direct&300|}}| | ||
| + | |||
| + | ==== General Screw Removal ==== | ||
| + | Phillips Head Screws: \\ | ||
| + | Always use the correct wrench for the screw heads you're working with. \\ | ||
| + | Using a too small Phillips screwdriver will strip the head of a Phillips screw. \\ | ||
| + | Not using enough force against a Phillips screw when removing or installing can strip the head of the screw. \\ | ||
| + | Using a short Phillips screwdriver with the correct size end leaves you less torque than using a long one. \\ | ||
| + | Then you have to push harder on the screw while turning and slippage of the tool begins. \\ | ||
| + | You can also use a screwdriver bit adapter on a socket wrench to give you more turning power especially when removing stubborn screw. \\ | ||
| + | It's not a good idea to tighten Phillips head screws with a socket wrench. \\ | ||
| + | A good thick long screwdriver is generally all that's needed. \\ | ||
| + | **Caution**: tightening Phillips head screws with a socket wrench can strip the heads of the screw. \\ | ||
| + | Loosening a screw: Always keep good pressure against the screw while turning it until it loosens up. \\ | ||
| + | Tightening a screw: Snug plus a nudge is all it takes to tighten these carb screws with a socket wrench. \\ | ||
| + | (especially with no torque specs in the service manuals) \\ | ||
| + | |||
| + | | Screwdriver bit attachment on socket wrench ((photo by Hippysmack)) | | ||
| + | |{{:techtalk:ref:tools:socket_wrench_w_screwdriver_bit_adapter_by_hippysmack.jpg?direct&300|}}| | ||
| + | |||
| ==== Jets ==== | ==== Jets ==== | ||
| Line 100: | Line 125: | ||
| - | ===== Intake Manifold ===== | ||
| - | |||
| - | |"Intake Manifold Wrench" - 'Z' shaped Allen wrench ((photo by Phillober of the XLFORUM http://xlforum.net/forums/showthread.php?t=1122547)) \\ Made for this purpose, available online ($10-$20)|This is a Bondhus Driver ((photo by biknut of the XLFORUM http://xlforum.net/forums/showthread.php?p=2292820)) \\ (basically a ball end Allen wrench with a handle)| | ||
| - | |{{:techtalk:ref:tools:mainiflod_wrench_by_phllober.jpg?direct&300|}}|{{:techtalk:ref:tools:bondhus_driver_by_biknut.jpg?direct&300|}}| | ||
| ===== Sleeve for Tuning Air / Fuel Mixture ===== | ===== Sleeve for Tuning Air / Fuel Mixture ===== | ||
