Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:tools129 [2018/08/25 16:34] hippysmack |
techtalk:ref:tools129 [2019/04/08 22:27] hippysmack [To Gap the Spark Plugs] |
||
---|---|---|---|
Line 5: | Line 5: | ||
===== To Gap the Spark Plugs ===== | ===== To Gap the Spark Plugs ===== | ||
- | |A small stainless plate 7/8" long by 3/8" wide and .040" thick with a \\ hole in it. It can be kept on a key ring and instead of keeping a feeler \\ gauge on your bike. ((Deep Diver of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=5))| | + | |A small stainless plate 7/8" long by 3/8" wide and .040" thick with a \\ hole in it. It can be kept on a key ring and instead of keeping a feeler \\ gauge on your bike. ((Deep Diver of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=5))|This tool is not scientific and it's use is subjective. \\ But it is widely used for gapping plugs. ((Hippysmack))| |
- | |{{techtalk:ref:tools:homemade-spark-plug-feeler-gauge_by_deep_diver.jpg?direct&400|}}| | + | |{{techtalk:ref:tools:homemade-spark-plug-feeler-gauge_by_deep_diver.jpg?direct&400|}}|{{:techtalk:ref:tools:spark_plug_gapper_by_hippysmack.jpg?direct&400|}}| |
- | ^ Homemade Spark Plug Gapping Tool ((photo by Deep Diver of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=5)) ^ | + | ^ Homemade Spark Plug Gapping Tool ((photo by Deep Diver of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=5)) ^ Commercial spark plug gapping tool. ((photo by Hippysmack)) ^ |
- | ===== Spark Plug Hole Adapters for Diagnostic Testing ===== | ||
- | |{{:techtalk:ref:tools:homemade_12mm-to_quarter_npt_hose_adapter_1_by_cjburr.jpg?direct&300|}}|{{:techtalk:ref:tools:homemade_12mm-to_quarter_npt_hose_adapter_2_by_cjburr.jpg?direct&300|}}| | + | ===== Flexible Extension for Dual Plug Heads ===== |
+ | Care should be taken when installing the top spark plug on S models or any with dual plug heads. \\ | ||
+ | It's easy to get into the wrong position and break the end of the plug with a conventional wrench. \\ | ||
- | |{{:techtalk:ref:tools:homemade_12mm-to_quarter_npt_hose_adapter_3_by_cjburr.jpg?direct&300|}}|{{:techtalk:ref:tools:homemade_12mm-to_quarter_npt_hose_adapter_4_by_cjburr.jpg?direct&300|}}|{{:techtalk:ref:tools:homemade_12mm-to_quarter_npt_hose_adapter_5_by_cjburr.jpg?direct&300|}}| | + | |
- | ^ Homemade 1/4" NPT to 12mm Spark Plug Hole Adapter ((photos by cjburr of the XLFORUM http://xlforum.net/forums/showthread.php?t=56497)) ^^^ | + | This flexible extension allows you to maneuver the plug into the hole using the handle on the end to start the threads without much force. \\ |
+ | This was once available at most auto parts stores and is still available online. \\ | ||
+ | If the plug doesn't thread easily, the grip will slip on the plug instead of forcing the threads together and cross-threading them. \\ | ||
+ | Then you simply back it out, re-position and try again until the threads are started correctly. \\ | ||
+ | Once the threads are started, remove the flex tool, use a conventional plug wrench to snug up and then a torque wrench for final tightening. \\ | ||
+ | |||
+ | | STEELMAN PRO 08310R flexible 12-Inch spark plug starter tool ((photos by Hippysmack)) ||| | ||
+ | |{{:techtalk:ref:tools:flexible_spark_plug_extension_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:flexible_spark_plug_extension_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:flexible_spark_plug_extension_3_by_hippysmack.jpg?direct&300|}}| | ||
\\ | \\ |