Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:tools129 [2018/11/01 04:09] hippysmack [Homemade] |
techtalk:ref:tools129 [2019/04/08 22:31] hippysmack [To Gap the Spark Plugs] |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| ===== To Gap the Spark Plugs ===== | ===== To Gap the Spark Plugs ===== | ||
| - | |A small stainless plate 7/8" long by 3/8" wide and .040" thick with a \\ hole in it. It can be kept on a key ring and instead of keeping a feeler \\ gauge on your bike. ((Deep Diver of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=5))| | + | A small stainless plate 7/8" long by 3/8" wide and .040" thick with a hole in it. \\ |
| - | |{{techtalk:ref:tools:homemade-spark-plug-feeler-gauge_by_deep_diver.jpg?direct&400|}}| | + | It can be kept on a key ring and instead of keeping a feeler gauge on your bike. ((Deep Diver of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=5)) \\ |
| + | |{{techtalk:ref:tools:homemade-spark-plug-feeler-gauge_by_deep_diver.jpg?direct&300|}}| | ||
| ^ Homemade Spark Plug Gapping Tool ((photo by Deep Diver of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=5)) ^ | ^ Homemade Spark Plug Gapping Tool ((photo by Deep Diver of the XLFORUM http://xlforum.net/forums/showthread.php?t=395586&page=5)) ^ | ||
| - | ===== Spark Plug Hole Adapters for Diagnostic Testing ===== | ||
| - | These are used in place of the spark plug to hook up diagnostic tools (compression tester, leak-down tester etc.). \\ They can also be used to adapt a 14mm TDC whistle or piston stop to a Sporty engine. | ||
| - | ==== Commercially available ==== | + | This tool is not scientific and it's use is subjective. But it is widely used for gapping plugs. ((Hippysmack)) |
| + | |{{:techtalk:ref:tools:spark_plug_gapper_by_hippysmack.jpg?direct&300|}}| | ||
| + | ^ Commercial spark plug gapping tool. ((photo by Hippysmack)) ^ | ||
| - | * 12mm adapters are usually supplied along with compression and leak down kits. They are also available at some auto parts stores and online tool companies. | ||
| - | * If you, by chance, have bought a 'kit' in the past only to find your gauges no longer work properly, keep the fittings that came with it before tossing out the defective parts. \\ These may prove to be invaluable when they are needed. | ||
| - | |A few adapters including a tall one (which is great for some V-8's). \\ Add the small 14mm-12mm adapter on the long one and it'll work for 12mm plug holes.|| | + | ===== Flexible Extension for Dual Plug Heads ===== |
| - | |{{:techtalk:ref:tools:spark_plug_thread_adapters_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:spark_plug_thread_adapters_2_by_hippysmack.jpg?direct&300|}}| | + | Care should be taken when installing the top spark plug on S models or any with dual plug heads. \\ |
| - | ^ Spark Plug Hole Thread Adapters ((photos by Hippysmack)) ^^ | + | It's easy to get into the wrong position and break the end of the plug with a conventional wrench. \\ |
| + | |||
| + | |||
| + | This flexible extension allows you to maneuver the plug into the hole using the handle on the end to start the threads without much force. \\ | ||
| + | This was once available at most auto parts stores and is still available online. \\ | ||
| + | If the plug doesn't thread easily, the grip will slip on the plug instead of forcing the threads together and cross-threading them. \\ | ||
| + | Then you simply back it out, re-position and try again until the threads are started correctly. \\ | ||
| + | Once the threads are started, remove the flex tool, use a conventional plug wrench to snug up and then a torque wrench for final tightening. \\ | ||
| + | |||
| + | | STEELMAN PRO 08310R flexible 12-Inch spark plug starter tool ((photos by Hippysmack)) ||| | ||
| + | |{{:techtalk:ref:tools:flexible_spark_plug_extension_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:flexible_spark_plug_extension_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:flexible_spark_plug_extension_3_by_hippysmack.jpg?direct&300|}}| | ||
| \\ | \\ | ||
