Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:tools130 [2020/06/22 19:13] hippysmack [Removal / Installation] |
techtalk:ref:tools130 [2020/06/26 03:05] hippysmack [Brake Cylinder Hone] |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ====== REF: Tools - 130 ====== | ====== REF: Tools - 130 ====== | ||
| \\ | \\ | ||
| - | ====== Brake Caliper / Master Cylinder Tools ====== | + | ====== Master Cylinder / Brake Caliper / Rotor Tools ====== |
| + | ===== Retaining Ring Removal / Installation ===== | ||
| + | Snap Ring Pliers from Carquest (PN STL46000): | ||
| + | The longer points on the end allow access to the snap ring in the front master cylinders to be removed. \\ | ||
| + | Some snap ring pliers are too big to get in there. | ||
| + | These were purchased from Carquest for less than $20. | ||
| + | |||
| + | {{:techtalk:ref:tools:snap_ring_pliers_by_fearlessfrisbee.jpg?direct&300|}} ((photo by FearlessFrisbee of the XLFORUM http://xlforum.net/forums/showthread.php?t=1509094)) \\ | ||
| ===== Caliper Removal / Installation ===== | ===== Caliper Removal / Installation ===== | ||
| 98 style rear caliper mounting bolts (2) require a Torx T-40 driver bit. \\ | 98 style rear caliper mounting bolts (2) require a Torx T-40 driver bit. \\ | ||
| Line 25: | Line 32: | ||
| |{{:techtalk:ref:tools:brakehone005_by_hopper.jpg?direct&300|}}|{{:techtalk:ref:tools:brakehone006_by_hopper.jpg?direct&300|}}|{{:techtalk:ref:tools:brakehone007_by_hopper.jpg?direct&300|}}| | |{{:techtalk:ref:tools:brakehone005_by_hopper.jpg?direct&300|}}|{{:techtalk:ref:tools:brakehone006_by_hopper.jpg?direct&300|}}|{{:techtalk:ref:tools:brakehone007_by_hopper.jpg?direct&300|}}| | ||
| - | ===== Retaining Ring Removal / Installation ===== | + | ===== Brake Disc (rotor) ===== |
| - | + | ||
| - | Snap Ring Pliers from Carquest (PN STL46000): | + | |
| - | The longer points on the end allow access to the snap ring in the front master cylinders to be removed. \\ | + | |
| - | Some snap ring pliers are too big to get in there. | + | |
| - | These were purchased from Carquest for less than $20. | + | |
| - | + | ||
| - | {{:techtalk:ref:tools:snap_ring_pliers_by_fearlessfrisbee.jpg?direct&300|}} ((photo by FearlessFrisbee of the XLFORUM http://xlforum.net/forums/showthread.php?t=1509094)) \\ | + | |
| + | |An impact wrench works for loosening the Torx bolts on the rotor to remove it from the rim. ((photos by Screw Loose Dan of the XLFORUM http://xlforum.net/forums/showthread.php?t=274658&highlight=brembo)) || | ||
| + | |{{techtalk:ref:tools:brembo_caliper_install_14_by_screw_loose_dan.jpg?direct&300|}}|{{techtalk:ref:tools:brembo_caliper_install_15_by_screw_loose_dan.jpg?direct&300|}}| | ||
| \\ | \\ | ||
