Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:tools142 [2018/07/21 03:19] hippysmack [Swingarm Tools] |
techtalk:ref:tools142 [2020/06/13 08:22] hippysmack |
||
---|---|---|---|
Line 2: | Line 2: | ||
====== REF: Tools - 142 ====== | ====== REF: Tools - 142 ====== | ||
====== Swingarm Tools ====== | ====== Swingarm Tools ====== | ||
- | ===== Swingarm Thread Repair Tool ===== | + | \\ |
+ | |||
+ | ====== IH Swingarm Thread Repair Tool ====== | ||
A wrecked right side bearing locknut 47515-52 [52 to E74] with a fitting welded into it. \\ Slots were cut into the threads and it is used to chase / repair the threads in the swingarm. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) | A wrecked right side bearing locknut 47515-52 [52 to E74] with a fitting welded into it. \\ Slots were cut into the threads and it is used to chase / repair the threads in the swingarm. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) | ||
Line 11: | Line 13: | ||
|{{:techtalk:ref:tools:swingarmthreads3_by_ironmick.jpg?direct&300|}}|{{:techtalk:ref:tools:swingarmthreads4_by_ironmick.jpg?direct&300|}}| | |{{:techtalk:ref:tools:swingarmthreads3_by_ironmick.jpg?direct&300|}}|{{:techtalk:ref:tools:swingarmthreads4_by_ironmick.jpg?direct&300|}}| | ||
| Swingarm thread repair tool ((photos by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) || | | Swingarm thread repair tool ((photos by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) || | ||
+ | |||
+ | ====== Pivot Bolt ====== | ||
+ | |||
+ | 93-03 swingarm pivot bolt wrench sizes. \\ | ||
+ | To remove the pivot bolt, remove the pivot bolt screw and turn the bolt a few turns to loosen it up. \\ | ||
+ | Put the pivot bolt screw back in a few turns and whack it with a hammer to initially drive it toward the right side. \\ | ||
+ | Then use a screwdriver to pry the bolt out while turning the screw. Continue turning while giving up pressure on the wrench to back the bolt out. \\ | ||
+ | {{:techtalk:ref:tools:pivot_bolt_screw_2925a_wrench_size_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:pivot_bolt_41568-81b_wrench_size_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | {{:techtalk:ref:tools:pivot_bolt_removal_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:pivot_bolt_removal_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | ====== Swingarm Bushing Removal / Installation ====== | ||
+ | |||
\\ | \\ |