Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:ref:tools142 [2019/12/02 03:10] hippysmack [Pivot Bolt] |
techtalk:ref:tools142 [2020/06/13 08:22] hippysmack |
||
---|---|---|---|
Line 3: | Line 3: | ||
====== Swingarm Tools ====== | ====== Swingarm Tools ====== | ||
\\ | \\ | ||
- | ====== Pivot Bolt ====== | ||
- | 93-03 swingarm pivot bolt wrench sizes. \\ | ||
- | To remove the pivot bolt, remove the pivot bolt screw and turn the bolt a few turns to loosen it up. \\ | ||
- | Put the pivot bolt screw back in a few turns and whack it with a hammer to initially drive it toward the right side. \\ | ||
- | Then use a screwdriver to pry the bolt out while turning the screw. Continue turning while giving up pressure on the wrench to back the bolt out. \\ | ||
- | {{:techtalk:ref:tools:pivot_bolt_screw_2925a_wrench_size_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:pivot_bolt_removal_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
- | {{:techtalk:ref:tools:pivot_bolt_41568-81b_wrench_size_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:pivot_bolt_removal_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | + | ====== IH Swingarm Thread Repair Tool ====== |
- | ===== Swingarm Thread Repair Tool ===== | + | |
A wrecked right side bearing locknut 47515-52 [52 to E74] with a fitting welded into it. \\ Slots were cut into the threads and it is used to chase / repair the threads in the swingarm. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) | A wrecked right side bearing locknut 47515-52 [52 to E74] with a fitting welded into it. \\ Slots were cut into the threads and it is used to chase / repair the threads in the swingarm. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) | ||
Line 20: | Line 13: | ||
|{{:techtalk:ref:tools:swingarmthreads3_by_ironmick.jpg?direct&300|}}|{{:techtalk:ref:tools:swingarmthreads4_by_ironmick.jpg?direct&300|}}| | |{{:techtalk:ref:tools:swingarmthreads3_by_ironmick.jpg?direct&300|}}|{{:techtalk:ref:tools:swingarmthreads4_by_ironmick.jpg?direct&300|}}| | ||
| Swingarm thread repair tool ((photos by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) || | | Swingarm thread repair tool ((photos by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) || | ||
+ | |||
+ | ====== Pivot Bolt ====== | ||
+ | |||
+ | 93-03 swingarm pivot bolt wrench sizes. \\ | ||
+ | To remove the pivot bolt, remove the pivot bolt screw and turn the bolt a few turns to loosen it up. \\ | ||
+ | Put the pivot bolt screw back in a few turns and whack it with a hammer to initially drive it toward the right side. \\ | ||
+ | Then use a screwdriver to pry the bolt out while turning the screw. Continue turning while giving up pressure on the wrench to back the bolt out. \\ | ||
+ | {{:techtalk:ref:tools:pivot_bolt_screw_2925a_wrench_size_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:pivot_bolt_41568-81b_wrench_size_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | {{:techtalk:ref:tools:pivot_bolt_removal_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:pivot_bolt_removal_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
+ | |||
+ | ====== Swingarm Bushing Removal / Installation ====== | ||
+ | |||
\\ | \\ |