Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:tools142 [2019/12/02 17:13] hippysmack [Pivot Bolt] |
techtalk:ref:tools142 [2020/06/13 08:22] hippysmack |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ====== Swingarm Tools ====== | ====== Swingarm Tools ====== | ||
| \\ | \\ | ||
| + | |||
| + | ====== IH Swingarm Thread Repair Tool ====== | ||
| + | |||
| + | A wrecked right side bearing locknut 47515-52 [52 to E74] with a fitting welded into it. \\ Slots were cut into the threads and it is used to chase / repair the threads in the swingarm. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) | ||
| + | |||
| + | |{{:techtalk:ref:tools:swingarmthreads1_by_ironmick.jpg?direct&300|}}|{{:techtalk:ref:tools:swingarmthreads2_by_ironmick.jpg?direct&300|}}| | ||
| + | | Swingarm thread repair tool ((photos by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) || | ||
| + | |||
| + | |{{:techtalk:ref:tools:swingarmthreads3_by_ironmick.jpg?direct&300|}}|{{:techtalk:ref:tools:swingarmthreads4_by_ironmick.jpg?direct&300|}}| | ||
| + | | Swingarm thread repair tool ((photos by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) || | ||
| + | |||
| ====== Pivot Bolt ====== | ====== Pivot Bolt ====== | ||
| + | |||
| 93-03 swingarm pivot bolt wrench sizes. \\ | 93-03 swingarm pivot bolt wrench sizes. \\ | ||
| To remove the pivot bolt, remove the pivot bolt screw and turn the bolt a few turns to loosen it up. \\ | To remove the pivot bolt, remove the pivot bolt screw and turn the bolt a few turns to loosen it up. \\ | ||
| Line 11: | Line 23: | ||
| {{:techtalk:ref:tools:pivot_bolt_removal_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:pivot_bolt_removal_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:ref:tools:pivot_bolt_removal_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:pivot_bolt_removal_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| - | ===== Swingarm Thread Repair Tool ===== | ||
| - | A wrecked right side bearing locknut 47515-52 [52 to E74] with a fitting welded into it. \\ Slots were cut into the threads and it is used to chase / repair the threads in the swingarm. ((IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) | + | ====== Swingarm Bushing Removal / Installation ====== |
| - | |{{:techtalk:ref:tools:swingarmthreads1_by_ironmick.jpg?direct&300|}}|{{:techtalk:ref:tools:swingarmthreads2_by_ironmick.jpg?direct&300|}}| | ||
| - | | Swingarm thread repair tool ((photos by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) || | ||
| - | |||
| - | |{{:techtalk:ref:tools:swingarmthreads3_by_ironmick.jpg?direct&300|}}|{{:techtalk:ref:tools:swingarmthreads4_by_ironmick.jpg?direct&300|}}| | ||
| - | | Swingarm thread repair tool ((photos by IronMick of the XLFORUM http://xlforum.net/forums/showthread.php?t=1532528)) || | ||
| \\ | \\ | ||
