Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:tools145 [2019/12/20 21:27] hippysmack [Oil Pump Check Ball Seat Lapping Tool] |
techtalk:ref:tools145 [2019/12/20 21:31] hippysmack [Oil Pump Check Ball Seat Lapping Tool] |
||
|---|---|---|---|
| Line 4: | Line 4: | ||
| ====== 57-76 oil pumps ===== | ====== 57-76 oil pumps ===== | ||
| - | \\ | ||
| - | ===== Oil Pump Check Ball Seat Lapping Tool ====== | ||
| See also in the Sportsterpedia: | See also in the Sportsterpedia: | ||
| * [[techtalk:ih:oil03#oil_pump|Main IH Oil Pump Menu Page]] | * [[techtalk:ih:oil03#oil_pump|Main IH Oil Pump Menu Page]] | ||
| * [[techtalk:ih:oil03g#oil_pump_damage_and_repair|57-76 Oil Pump Damage and Repair]] for ideas on a fix for wet sumping from the oil pump. \\ | * [[techtalk:ih:oil03g#oil_pump_damage_and_repair|57-76 Oil Pump Damage and Repair]] for ideas on a fix for wet sumping from the oil pump. \\ | ||
| + | |||
| + | ===== Oil Pump Check Ball Seat Lapping Tool ====== | ||
| **The tool on the left** is a homemade check ball lapping tool used to lap the seat where the check ball sits in the oil pump (57-76). \\ | **The tool on the left** is a homemade check ball lapping tool used to lap the seat where the check ball sits in the oil pump (57-76). \\ | ||
| Line 24: | Line 24: | ||
| You'd probably need a lathe, a tap set and the ability to braze or silver solder to make your own tool. \\ | You'd probably need a lathe, a tap set and the ability to braze or silver solder to make your own tool. \\ | ||
| Although you might drill out and tap an un-needed pump nipple for part of the tool. \\ | Although you might drill out and tap an un-needed pump nipple for part of the tool. \\ | ||
| + | You can indicate the bolts in the chuck, face off the ends and then center drill them to provide a concentric pocket for the sphere to rest in. \\ | ||
| + | Then, hold the whole mess in tension between centers as you soldered. They surely have to be straight or they aren’t much use. \\ | ||
| |{{:techtalk:ref:tools:homemade_check_ball_lapping_tool_by_toolmaker.jpg?direct&300|}}|{{:techtalk:ref:tools:oil_pump_check_ball_lap_by_dawind.jpg?direct&300|}}| | |{{:techtalk:ref:tools:homemade_check_ball_lapping_tool_by_toolmaker.jpg?direct&300|}}|{{:techtalk:ref:tools:oil_pump_check_ball_lap_by_dawind.jpg?direct&300|}}| | ||
| Line 32: | Line 33: | ||
| ====== 77 and later oil pumps ====== | ====== 77 and later oil pumps ====== | ||
| - | \\ | + | See also in the Sportsterpedia: |
| + | |||
| + | * [[techtalk:evo:oil03#oil_pump_unit|Main Evo Oil Pump Menu Page]] \\ | ||
| ====== Retaining Rings ====== | ====== Retaining Rings ====== | ||
| These precision cuticle scissors are great for removing external retainer rings. \\ | These precision cuticle scissors are great for removing external retainer rings. \\ | ||
| Line 48: | Line 52: | ||
| ====== Oil Pump Removal ====== | ====== Oil Pump Removal ====== | ||
| - | See also in the Sportsterpedia: | ||
| - | |||
| - | * [[techtalk:evo:oil03#oil_pump_unit|Main Evo Oil Pump Menu Page]] | ||
| Mounting bolts (to the engine): \\ | Mounting bolts (to the engine): \\ | ||
