Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:ref:wheels06a [2019/06/30 01:30] hippysmack [Clean All Old Brake Fluid Out of the M/C] |
techtalk:ref:wheels06a [2019/06/30 02:21] hippysmack [Test the M/C] |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| \\ | \\ | ||
| ====== An Exercise in Bleeding the Brake System ====== | ====== An Exercise in Bleeding the Brake System ====== | ||
| - | Link to this page: \\ | ||
| - | See also [[techtalk:ref:wheels06a|An Exercise in Bleeding the Brake System]] \\ | ||
| The test subject is a brake lever and master cylinder from a 95 Kawasaki but the process is the same for a Sportster. \\ | The test subject is a brake lever and master cylinder from a 95 Kawasaki but the process is the same for a Sportster. \\ | ||
| Line 21: | Line 19: | ||
| {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_1_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_3_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_5_by_hippysmack.jpg?direct&300|}} | {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_1_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_3_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_5_by_hippysmack.jpg?direct&300|}} | ||
| - | ====== Test the M/C Pressure ====== | + | ====== Test the M/C ====== |
| + | **For a pressure squirt**: \\ | ||
| With new fluid in the M/C, before attempting to move fluid or bleed the air, lightly squeeze the lever or pedal. \\ | With new fluid in the M/C, before attempting to move fluid or bleed the air, lightly squeeze the lever or pedal. \\ | ||
| Watch for a spurt of fluid from the hole in the bottom. \\ | Watch for a spurt of fluid from the hole in the bottom. \\ | ||
| Line 29: | Line 27: | ||
| If using DOT 5 fluid, this is a simple matter of cleanup with a rag. \\ | If using DOT 5 fluid, this is a simple matter of cleanup with a rag. \\ | ||
| If using DOT3,4 or 5.1 then it needs to be hose off with water immediately as these type fluids will eat your paint. \\ | If using DOT3,4 or 5.1 then it needs to be hose off with water immediately as these type fluids will eat your paint. \\ | ||
| - | {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_8_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_9_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_10_by_hippysmack.jpg?direct&300|}} | + | {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_8_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_9_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_10_by_hippysmack.jpg?direct&300|}} \\ |
| + | |||
| + | **For air bubbles**: \\ | ||
| + | With the cap off, tickle the lever / pedal and check for air bubbles to come up inside the M/C. \\ | ||
| + | If you see any bubbles, before sending these down the brake line, continue to tickle until they are no longer created. \\ | ||
| + | {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_11_by_hippysmack.jpg?direct&300|}} {{:techtalk:ref:wheels:excersize_in_bleeding_brakes_12_by_hippysmack.jpg?direct&300|}} \\ | ||
| + | |||
| + | ====== How Air Bubbles Move ====== | ||
| + | |||
| + | Here's a short video on how the air moves as the lever is tickled. \\ | ||
| + | {{:techtalk:ref:wheels:tickling_the_brake_pedal-lever_1_by_hippysmack.mp4 |}} ((video by Hippysmack)) \\ | ||
| \\ | \\ | ||
| - | + | ||
| + | ---- | ||
| + | \\ | ||
| [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
